| Blogs | Forums | Photo Album |
board
I`ve installed water resistant dyrwall throughout the bathroom with cement board in the bathtub area. The ceiling is all water resistant drywall sparingly including over the tub.
I`ve a amount o...
If one is planning to do the IC swap on the "D" board of a Sony KP-46WT510, are there any dangerous voltages present on the board itself? (in a power-off, unplugged state, of course!)
The...
i have 2 boards pn 6080127 rev 8 that were zapped by a power surge. some components are missing .some components were desoldered from the heat. i would appreciate a schematic or a picture of the board...
this board is probly no longer avaible their was several law suits against ge.
you may have to fix board look fore dark spot on board may indicate bad solder make sure board is mounted correctly and ...
where can i get a auto convergence board
What does a pico fuse on the convergence board look like?
...den floor and seem to have had a problem measuring, since the expansion gap is just to wide for the base board to cover.
I don't particularly want to go for a thicker base board, and was wonderi...
i have never been fussy about a waterproof backing board ,i just use 3/8 plasterboard use the correct adhesive and buy water proof grout not water resistant in powder form the waterproof comes ready m...
If this helps anybody than It'll be worth it......what I did with that burnt resistor R-95 on the board was removed it and replaced it with a 2 ohm 5 watt ceramic resistor than re-soldered the te...
how to install logic board
I have problem with my Mitsubishi Projection Tv. Pictures have shadows as if duplicated, power supply board appear burnt. But TV powers up. What should I do?
We have been able to hear water rushing through the pipes of our baseboards this year and have never noticed this in the past. Husband bled all the valves of air when we first turned it on. Now, even ...
hello I am a t.v. tech by trade with about 25 years exp.most of the 27 inch magnavox have one main board.not sure if it is called the s board or not.never heard of a speed board.the main board sometim...
I noticed something new! There is a tall vertically mounted board about 6in high just to the left of the tuner. It has a metal brace that is fastened to the main chassis board and extends to the top...
...t out and came on when it cooled. I took the back off (smart enough not to put in hands dont worry.) the board with the huge coil (looks similar to motorcycle ignition coil) had resisters sparking and...
I think it is something with the logic board. I took the logic board out of the working opener and swapped it with logic board out of the bad opener. After this, both openers worked fine for a few d...
the micro and eeprom on these boards are not meant to be changed.you should replace the whole board if is available.unless you have the right setup as far as needle point irons and microscopes and chi...
...m, but i changed the cap mentioned. still have 10.6 v once the white cord 3 plug plugged in from smaller board.then 12.12 v when not plugged in. i'm having someone more expirenced with electronic...
I have the same problem with my ASKO 10505 washer. Isolated the problem to be either the control board or the motor (the brushes and belt is fine). I need a schematic ASAP to test the voltages on the ...
... Raleigh it is a 3,300 uf (microfarad), 10 volt not 16volt. (Question: makes a difference?)
It is the board right in the middle of the back of the screen, has 8 screws and 7 connectors. The 2 capac...
and lay over old cement board?
which is better? would removing the old tile and cleaning the old cement board be a huge amount of work?
Please advise
there is three yellow fuses in front of the i.c.when looking at the d board while in the set.right in back of the red green and blue yoke plugs.may be hard to get your meter in there with out hitting ...
I have the same problem on my 1991 Mitsubishi 50". The problem? The POWER
SUPPLY BOARD. In my humble opinion, this
board's solder points are not solder real
good. Some solder points get b...
...SUPPLY HAS BEEN REFURBISCHD( ALL CAPS UPGRADED, AND ALL VOLTAGES ARE OK, 24V GOES AND REMINS AT INVERTER BOARD ? NEW BOARD NOT AVAILIBEL. CAN IT BE BY PASSED?
THERE ARE 8 TUBES WAT VOLTAGE AND FREQWE...
yes that would be a good place to start.other then the main board and the controller board theres not much left to control the picture but the panal itself.
The swap worked so the new board is on its way. Thinking back on the diagnostic work, it had to be the board because of the 3 volt situation when it should have been running at 6v. Thanks for the adv...
this tv is a mitsubishi.it is noted for bad solder under deflection board around flyback theirs a STE130VOLT DC 5 AMP REGULATOR GETS HOT LOOSENS UP SOLDER.look with magnafi glass you will see solder r...
NEED HELP HAVE A GE HOTPOINT WHICH THE TOLD ME IS THE BOARD WR55X151. HAD TRIED BUT TWO OF THEM HAD THE FILTER BAD NEED TO FIND PROBLEM THAT MIGTH CAUSE THE BOARD TO GO BAD
chances are their nothing wrong with the orginal board be ware of solder rings on horizonal board and convergeance board.this tv is noted fore this.look around 30vdc source off flyback theirs a small ...
I PAID A REPAIRMAN $330.00 TO FIX THE PROBLEM. A CIRCUT ON THE BOARD WAS DAMAGED.
t .The REPAIRMAN SAID IT WAS BECAUSE THE BOARD OVERHEATED DUE TO LEAVING REFRIGERATOR DOOR PARTIALLY OPEN. HE SAID N...
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...