build
... http://www.grainger.com/Grainger/items/5YL43?
BaseItem=5YL46
(this one is a little chunky though)
Build your own:
http://www.lowes.com/lowes/lkn?action=productDetail&
amp;productId=171679...
...er heater if possible - I will also purchase a water activated valve to shut off supply and gas).
Can I build a small (4-5 inch) containment wall/dam? What is the best method and material (concrete, ...
...iner to be installed, then 'bedding mortar' is installed over the liner (20 mil PVC) or pan to build the 'slope', then the tile is installed on the mortar, then grouted. Grout is n...
...stem.
I was just reading an article on a developer who renovated old "abandoned heritage" buildings downtown to build affordable housin and housin for seniors. One of his improperly in...
I plan to buy a new lot and build a small house. My concern is which part of the kitchen should i put my pull out cabinet where i stock my baking pans and cookware and another pull out cabinet to put...
I had a GMPP 350 H.O. crate engine that I am planning to build into a 383. All I'm going to reuse from the original engine is the block (heads and pistons are trashed). I am planning to use Dart ...
... second when i turn the key to the on position, but only if i crank the car for a bit does any fuel even build up in the fuel rails.
Any help or ideas would be greatly appreciated as tomorrow i wil...
...ate or just don’t work. diydoddle.com sells products for decorating, refurbishment, restoration and self-build projects.
The secret to successful DIY is in preparation and protection. If a dust sh...
...have a manutech curent since transformer I pickewd up from a junk box buy, and I've been tyriung to build a simple kill-a-watt meter. Here is my schematic:
3 to 2000 created by Andy´s A...
...would like to take sheet aluminum and connect the gunnels to the floor for more rigidity. next i want to build a center console. i do alot of catfishing and the current layout of the boat is just simp...
Hey I have to build a DC motor for my Phy class. It cannot be simple, meaning, it needs to have brushes and a commutator.
I made an armature from a cylindrical wood block, I put nails on each side s...
...llows moisture to pass through due to gravity) NOT silicone (which holds back the moisture forcing it to build up, and cause further problems).
If they did not install this properly, it was not bui...
...m figured out, now I need some help with the following things:
- What items do I require?
- How do I build a such device (screen, normal calculator buttons: 0-9,+,-,*,/,c, bluetooth capabilities) ...
To all intents and purposes there seems to be a growing trend to build boats (especially competitive specially sailing boats) brutally using vinylester resin, rather then epoxy or polyester. To that ...
I apologize ahead of time, as I wasn't sure where to post this.
I need to build a retaining wall along the side of a canal, but need to make it aesthetically pleasing. Most of the canal is lin...
I want to build storage shelves around the top perimeter of my garage, inside. The shelves will be attached to the wall on one side and "hang" from the cieling on the outside edge. I want to...
...ither the mix valve(if there is one) is failing just have to replace... or the coil has too much mineral build up in it, the best way to fix in this case is to abandon it and go with a indirect fired ...
...d revokeing moderator position. i no longer want i will just sit and watch down fall of the site. i help build 3yrs ago long before you guys.
how come theirs clients going unanswered where are you ??...
...ion module was intermittant function that controls fuel pump relay to cancel fuel pump to keep from fuel build up in the intake manifold.between 1986 and 2007 30 million fuel pumps were replaced to la...
I'm not feeling sticky valve here...
Three things it could be, compression, fuel, or spark. You can eliminate compression by using a compression tester. The numbers should be close, 10psi +/...
...ough torque, and be geared low enough so you dont have to mess w/ gearing. the easiest thing would be to build the "bit" out of some flashing rivetted into a cone w/ more flashing for the bl...
...d slopes from bottom of the screen to the top). Somebody who has done this before said I should probably build up to the higher end by digging deeper on the low end and adding an extra row of rocks. ...
Just judging by the adverts on the forum, are you and most of the members from the Land Down Under? Yay or nay, it's one of the places I'd like to visit one of these days.
If I thought it...
Hi There
Nice to meet everyone.
I am busy with a DIY project building a Dome. To build my dome, I am using a pipe that is centered onto a board. Attached to the pipe is a spinner with a wood cut...
I am posting this article in hopes someone else with the same engine may find this information useful; for I spent quite a long time figuring this one out.
First of all, let me just say that if you a...
...that you'd like to see listed.
NOTE:
Be sure to ID where you would like your entry to go,
ie: Build-Repair/Home/Appliances
(if you were wanting an Appliance Sub-Topic in Home).
.
.
.
...
...little fireplace in it. Obviously the thing hasn't been used in years but I've been wanting to build a fume hood (its a box for doing chemistry in which sucks out toxic fumes) for a while no...
...il leak. price 65,000 for the engine short block with out heads and 4,000 labor to replace. they had to build up engine he though this was cheap. to replace at that time was 85,000 to 97,000 for a ne...
...t off again.the fuel pump relay is design to shut off fuel pump when module is going bad to prevent fuel build up in the intakes so engine does not explodes in your face.from 1986 to 2000. 10 billio...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...