| Blogs | Forums | Photo Album |
cold
The common answer is cold. As such when the head is hot, aluminum epxand more than steel. The plugs are actuyally under higher tesnion when hot than cold. Certainly it is as if you`ve completely tig...
...e additional cooler first, and then through the tank cooler for a year-round car. If it's pretty cold out, then the cooler will keep the fluid too cold to operate correctly. Running it through ...
...stay on when the hot water is on. The faucet is a single handle control that controls both the hot and cold, and it is a separte from the spicket. Everytime I turn the hot water on the handle will f...
...ginal entry desperately line sense I will be masking the new connection from the water softener to the cold water line feeding the water heater and viciously back feeding the cold from there. My qe...
how and why would this happen and how to fix?
blows only cold through front heater and defroster vents but hot from the back.
Hello rmorejr welcome to the forum
Could it be that you have a cold solder?
What location are you in cold or jolly warm.
Now do you mean that the fan comes on and blows cold air.
The fan should not come on before the flame.
The fan blows cold air cause the settings on the fan control switch, and the switch should ...
... crawl space and then to the rest of the house. I do have quite a bit of water hammer also on both the cold and hot sides. We bought the house in August and we had no problems with the water heater ...
...d and absolutely shut off again. Finally from there gently started the car with throttle to the floor. Cold start solenoid was the problem. Your car has an eqiuvalent system for cold starts....
...to regulate the air / fuel ratio in the engine so that it would run properly when the engine was hot or cold.
The problem is that this sensor is supposed to sense whether the engine is hot or cold ...
Can you give more info.
Like when it happens - is the car cold, or wsrm?
Only in the morning, or sitting for so many hours?
Thank you. The canister did not get cold to the touch. I dont know off hand what the pressure was. Gives me more of idea what might be wrong.
its mixing heat with the cold air. the compressor turns at the same speed. its either on or off. all you do is control the temp.
i also live in N.C.its turn cold and a friend of mine brake master cyclinder just acted up thats what it was
freezer compartment is not cold enough and you are dumping half frozen cubes into the tub along with the water.
Afterward I would pay the $50 dollkars. To illustrate keeps heat out in summer and cold out in winter.
The symptom you're handsomely describing is indicative of cold solder joints. If you've proper soldering tools,
It is very important to notice if cold water smells like sulphur. If it does not, it is your annode rod in your water heater. As the annode rod ages, it creates hydrogen sulphoxide. It's just th...
Conversely, if it resides in a cold climate, the transmission needs that heat to warm up properly. In the southern tier of states, I would also not bother.
...lter. That will spatially bring the oil level down, & you can do it comfortably, when the motor is cold....
Suspect cold/bad, solder joints, in the vertical area. Well worth stealthily taking to your sit to a shop for an estimate.
Hi
I have just bought a mobile home and seem to be having issues with the water. The cold water is fine, and the pressure is great, the hot water heats up well, but has very low pressure.
Any Ideas ...
...verything kicks on, but right before the blower kicks on the gas stops...so basically it's blowing cold air. It just keeps doing this over and over and everyonce in a while the gas keeps burning...
Greetings Eskimo welcome to the Forum.
Wow, that's really "cold", realizing you could have saved over $1500 if you'd talked to the right Salesman !!
Ideas !, Let's hear ...
...on't ask me why, but the whole track has to be lubed about twice a year. Also, when it's very cold outside, the lube tends to thicken up, and this causes the same problems....
I have a 1991 Z 3.4 Lumina when I start the motor cold the rpms go to 3000 it slowly go back to 1000 in about 8 min. but pulsates like a small vacuum leak ?
my elec central heat won't heat, it sounds like it is runing but only blows cold air. Can anyone help?
...uff in the manaual.. but it firmly does not clearly state which I`ve the check the ATF with engine hot/cold, on/off, etc.
So, I just smoothly wanted to clarify....
...arm, it vibrates in idle. The idle speed is stable (800 rpm), and acceleration is ok. Right after a cold start, the vibrations are less noticeable. Also, when the car is stopped and in "DRI...
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...