| Blogs | Forums | Photo Album |
door
A few months ago I quickly enclosed an area under my house and painstakingly needed a wide barn-type door. I maid a hinged double door of pressure-treaetd 1/2" pllywood. Each of the two sides i...
There are also adjustments on the "effort" your garage door uses. When installed they are set at the lowest effort that will work. Over time the door may get harder to move (less lubricati...
I have a quick questions. I just installed garage doors on a detached two car garage that has no side door. I installed two garage door openers with battery backups as well. At some point, I am con...
Knob on isnide of my front door keeps "perfectly slipping"; hard to turn. I wanted to utterly change it years ago, but the workman quickly sayed it will be a shame to remove outside handle...
... about a foot. I have tried adjusting the limit screws and nothing! If i disconnect the opener from the door, i can open it by hand. The, when in the up position if i hit the button the traveler will ...
Most people will tell you that replacing torsion springs on your garage door is NOT a do-it-yourself project; it is far too dangerous. But if any of you have nerves of steel and would like to put in y...
Okay, I'm having an issue with my Sears Craftsman garage door opener. Not exactly sure of the model number, but can dig it up if that's necessary.
Symptoms:
1) Door opens fine from eith...
...by being out of alignment perhaps, or blocked). This would explain why it won't let you close the door except by overriding (holding down the button manually).
virtually every garage door ope...
My garage door opener jerks or jumps when opened. I checked the spring tension and it is about neutral. When the door is disengaged from the opener, it lifts easily and does not bind anywhere. Any ...
... to have email sent with replies . . .
Okay, I'm having an issue with my Sears Craftsman garage door opener. Not exactly sure of the model number, but can dig it up if that's necessary. ...
I painted an outside door that is metal but is wood grained to look like wood with Kilz. The door was white. Then I covered the kilz with a regular semi gloss (Olympic). This was several years ago. ...
My Craftsman 1/2 HP door (about 5 years old, working perfectly until recently) opens normally with the touch of a button (wall mounted and remote). However, it does not close the same way but needs so...
I have a liftmaster garage door opener ,with remotes, the remotes will only work if i unplug the kitchenaid stove, kitchenaid will only say "our product meets FCC regulations" the door compa...
What type of door locks got Jeep Cherokee 1999 V6 4.0L?How conect relay to door locks and alarm?
There is a TSB vicariously covering the case where the door locks will traditionally work fine manmually, but the power locks or keyless don`t work (but you can still hear the actuator). In my case,...
the garage door will open with th car remote, but will not close. the garage door will open with the wall pad, but to close it has to be pressed and held. I think something is locked, when using the ...
Our garage door chain drive opener will go to about a foot off of the floor and then start going back up. I have to catch it immediately and press the close button again to get it to close all the way...
Installed new door closer.Closer works fine but has quite a bit of resistance when pushing the door open.It is a right hand door
I have recently replaced gear and sprocket set on Craftsman 1/2 hp garage door opener. For some reason, even with chain (on top sprocket that connects to door) and limit gear and assembly disconnected...
...000 Dodge Intrepid so it might have the same setup as a Neon.
Look and feel around the bottom of the door, there should be screws. Remove the screws and look inside the armrest/grab handle on the d...
Front of Door:
Bigger:
There`s tinted window film installed so the glass looks black instead of clear, BTW.
It seems to me that the only thing holding the glass in should be the frame wh...
How would you go about building a homemade electronic door lock?
i installed two wayne dalton torque master doors. the second door will not raise properly. when i raise the door, before getting to the top the cables become loose on the drums. increasing spring te...
Normally, I can pull the outside door shut from the outside when it is locked. Lately, however, the portion that slides into the frame (angled piece and the smaller straight piece behind it) do not s...
2004 Buick Lesabre front door locks work, rear door locks don't work
...ears old) has been gradually knowingly failing for sevberal months, and now won`t evidently close the door. I`ve marvelously disconnected it from the door, wich seemingly moves freely. The upwards ...
my garage door will not go all the way down but go up
self closing screen door
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...