door
There are in fact knockouts to accomaodate the hinge mounting plate. I had the door reversed and the latch engaged, however the machine would "click" and readout LE...."door not locked&...
These are generally controlled with a spring loaded door switch. Possibly the door isn't closing closing properly or the plunger is bent.
my garage door will only open about 6 inches
... to have email sent with replies . . .
Okay, I'm having an issue with my Sears Craftsman garage door opener. Not exactly sure of the model number, but can dig it up if that's necessary. ...
I painted an outside door that is metal but is wood grained to look like wood with Kilz. The door was white. Then I covered the kilz with a regular semi gloss (Olympic). This was several years ago. ...
...t bought a used Asko Washing Machine. After my first load finished it's cycle, I pressed the "Door" button, but it did not open. Any suggestions?...
Hello -- first off, thanks to any one that can assist!
I have a Craftsman 1/2hp chain drive garage door opener (double door), and started having issues over the summer with the down operation. To ...
...you feel is fair. Your labor market will be different from that of anyone else.
An exterior prehung door should/will cost more than an interior door. Do you want the job to include trim and finis...
I have a liftmaster garage door opener ,with remotes, the remotes will only work if i unplug the kitchenaid stove, kitchenaid will only say "our product meets FCC regulations" the door compa...
i installed two wayne dalton torque master doors. the second door will not raise properly. when i raise the door, before getting to the top the cables become loose on the drums. increasing spring te...
wired from one side of garage door snapped can't lift the garage door open
final hours of installing new tile floors. exterior door theshold removed, needing to be replaced. new tile extends into door frame, under new threshold location. how do we properly install new thr...
I need to replace the rubber/vinyl insert in the threshold in 3 exterior doors.
I've tried to remove the inserts - but they're tough little buggers, and I'm splitting off the edges. ...
Have a Chamberlain 1/2-HP chain drive garage door opener. Door will now will operate in only one direction. Removed motor panel to observe up/down limit switches. When activated, the motor will run...
I have a craftsman 3/4 hp screw drive. Door would only come up 18 inches then stop. Released the door. The carriage is in full close position,screw will not stop. Horrible grinding sound and will not ...
Thanks Lex!
However, if a gear is stripped wouldn't the door just not close at all? Also, there are no issues with the door opening..
I have recently replaced gear and sprocket set on Craftsman 1/2 hp garage door opener. For some reason, even with chain (on top sprocket that connects to door) and limit gear and assembly disconnecte...
Normally, I can pull the outside door shut from the outside when it is locked. Lately, however, the portion that slides into the frame (angled piece and the smaller straight piece behind it) do not s...
It could be as simple as the door jam switch not working.
somewhere in the door jam will be a push button, and these break or stop working without notice.
Do the other doors work and just one do...
I have a Craftmans Garage Door Opener Model: 139.53960. It was working fine until yesterday. When I try to close it is not closing, But the light bulb is blinking 10 times.
I checked the motion senso...
What type of door locks got Jeep Cherokee 1999 V6 4.0L?How conect relay to door locks and alarm?
does astro vans have a trap door to get fuel pump out or do u have to drop tank
After replacing the sprocket assembly the door will only open for a few seconds and reverse and the light flashes 10 times as if there is an obstruction. I have checked the sensors, they are on and l...
2004 Buick Lesabre front door locks work, rear door locks don't work
My '95 low miles Buick Century 4 door will recycle the electric door locks until I can turn off the ignition. Then it will repeat. If I leave the car overnight, 98% of the time it will not repeat...
my garage door will not go all the way down but go up
I have recently replaced gear and sprocket set on Craftsman 1/2 hp garage door opener. For some reason, even with chain (on top sprocket that connects to door) and limit gear and assembly disconnected...
Installed new door closer.Closer works fine but has quite a bit of resistance when pushing the door open.It is a right hand door
Hello
I have a hollow core door that is unfortunately bowed - probably due to exposure to water , and I was wondering if anyone had any Ideas on how I could straighten it out?
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...