door
i need to know how to change door locks on a 97 monte carlo
My garage door will go up with the remote but it will not go down. You have to hold your finger on the inside mechanism until it goes all the way down. It's a new remote from Sears. What could...
does anyone have any idea about garage door openers? It seems mine is going halfway down and then stops....the chain has to have come undone at some point...any idea how to fix this problem?
Where is the door lock relay located on a 1994 chevy blazer 4wd?
Have a Chamberlain power drive door opener..It has 2 adjusting screw for up and down....have tried to adjust those with no results. dorr only moves about a foot and stops when its the up position. Any...
Hi everyone,
This is going to sound really stupid, but yesterday the inside handle of my UPVC front door snapped off in my hand!
Its usually quite hard to lock, but i guess i must have just ...
Both the keypad and the remote doesn't open the garage door in the morning but works fine later in the day.
How can this happen?
Hi
we got an out door fire pit as a gift, but we lack in places to use it, and our only option would be a wooden deck. Is that a bad Idea? or how could be use it on the deck without it being complete...
I have a Craftsman 1/2 hp garage door opener with a remote keyless entry and a remote opener in the car. I recently replace the batteries in both. Now neither work in the morning but work in the eve...
Does anyone know where I can find a IPB for a Craftsman 1/2 HP Garage Door Opener, Part # 11A5483-2 MFG 09/02.
The Gear that turns the chain broke, actually the shaft, that holds the gear, that tu...
Buick 2005 driver door release mechanism won't release and door won't open - locks appear to work fine.
Hi
I have a Honda Cr-V 2000, and the rear hatch door won't open with the help of the handle, so I am figuring something must be wrong with the handle.
I Sprayed some PB blaster in the mechanism...
Hi Mike10, welcome here
Perhaps THIS thread on our forum (please click here) can be of help?
...ears are not close enough together. There are adjustment screws on the side and the back of the garage door opener but I don't believe they would impact this adjustment. It did appear there was...
i have a jvc vhs camcorder
gr-ax637.the cassette door fails to open,although i can hear some whirring inside as if it were trying.is there any easy solution to this problem?
any help would be apprec...
i have a jvc vhs camcorder
gr-ax637.the cassette holder door fails to open
though it sounds like it is trying to.
any help would be appreciated...thanks
I have a 1/2 hp craftsman garage door opener with an entry pad. Can you tell me what battery I would need to buy for the entry pad?
after 20 years, I had to replace the cable of our garage door opener, because it finally snapped. I bought a cable and a repalcment connecting link from sears, and after one day the link snapped open....
I have and older Craftsman garage door opener. It is model number 139.53629srt. I would like to buy a wirless keypad for this open. What key pad do I need to buy and where can I find one?
my craftsman garage door worked fine last nite then this morning when i went to open it, it did not open and made a bunch of noise, any suggestions? i used the button in the garage to try and open.
...orum.
After sucessfully replacing my kitchen faucet last weekend, I thought I'd revisit my back door, which I ended up breaking the double pane glass to after locking myself out of the house a...
Please help me fix my disaster. I bought a steel exterior door from Home Depot that was installed on our Tuff Shed. This one here:
http://www.homedepot .com/webapp/wcs/stores/servlet/ProductDisplay...
Some of my Doorknobs have stopped catching - is there anyway this can be fixed or do I need to replace them?
I cannot for the life of me see how the keypad was mounted to the outside of the garage.i need to remove it.....i know it can;t be difficult yet I haven;t figured it out...........any help? thnx in ad...
replaced worm and drive gear in craftsman half horse opener. now it only goes a short distance and backs up with or without chain attached. i think it has something to do with the limit switches or th...
My shower doors are chrome finished aluminum. Would it be ok to sand them and get a brushed aluminum look? Will this effect the finish as I believe the manufacturing process includes a "sealing&q...
i have 2 boards pn 6080127 rev 8 that were zapped by a power surge. some components are missing .some components were desoldered from the heat. i would appreciate a schematic or a picture of the board...
Hi All -
I am new to the forum and would love to get some feedback/advice from anyone who can help me locate on line the metal support/frame system that I can screw some acrylic paneling.I have be...
I've read many of the complaints regarding the remotes but have yet to see my particular problem...We moved into a house in '06 and within that year purchased 2 new craftsman remotes. Only ...
I have a feeling mine is a bit to thin...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...