drive
...when i was leaving a store i put it into reverse just fine and backed out of my spot, but when i went to drive forward it wouldnt go into any gear. i have never had a problem with getting my car into ...
...1/2 hp garage door opener problem
I've replaced the sproket assembly in my 1/2 hp Craftsman chain drive opener and now the unit will only runfor about two seconds one directionand then two seco...
...ooler in my class A, (The previous owner apparently needed it). and I don't tow anything, and never drive in high mountain terrains, I was concerned that maybe my tranny oil was not getting hot ...
... or the other will be at least 25% of the value of the car.
I think that we will do the work and then drive the car till it drops. Right now with the way it isn't running, don't think we...
1993 G20 infinity trans that goes into Reverse just fine but hesitates to go into Drive especially when cold. The first step was to change the trans filter and install Castorl import ATF. Can the ba...
...k i have done .drain fluid change filter and two bottles trans-x or transmedic and can sealent stop leak.drive for a week or two you have nothing to lose either way you have to decide.cheap first befo...
...a severe lack of power below 2 thousand revs. I have noticed the temp gauge can read cold even on a long drive. Its does show some life occasionally tho. When I start the car from cold it chugs and sm...
...think that somoene could commonly be so damn stupid and still be alive, much less ordinarily alowed to drive a vehicle on a public street. For one I correctly assume that if anyone wants to see a p...
...ung(stretched) and its not opening the clutch.. what i could do was put it in 1st gear, start it up and drive off in first and then pull it into 2, then 3, then 4... but never back into 1st. gear w...
...l go. So I have to keep the fan going all the time or it will not start again by itself. It has a direct drive system so no belt...Does it have to be oiled and if so where do you oil it?...
...ong bolt into the hole (spark plug hole) until bottom is out on top of piston. You then use a hammer and drive to loosen the clutch....
...and clean-ed out the EGR valve.
Hopefully that will do it for a while and my teenager will be able to drive this car that I bought so he could use it and my wife and I can stop playing taxi.
I h...
Awesome thanks you guys for the help, I will be replacing that shortly. Yeah its a little tricky to drive her in lots of traffic haha.
Do you think it would be a bad idea to get a clutch master cy...
... the snowblower until you see the place where the shear pin has to go (the place where two parts of the drive shaft come together), remove old shear pin and slide in the new ones, tighten the nut upo...
...hink it is the "best"!
For me, the choice amongst Pygmy & CLC went to the fact I could drive over to Port Townsend and test paddle the Pygmy boats. I`m glad I did, because I _thoug...
...over a year old. I called HP (since Staples says its not their problem) and they are telling me the hard drive or motherboard is bad. I can send it in for repair at approx 350$ or as they recommend bu...
... snowblower (1965-1966 vintage). It ate a stick, and now the main auger is indep of the chute auger and drive mechanism. The chute auger spins properly. The shear pins were fine, although I broke o...
...he unmarked material needs to be removed. You may find the Dremel very slow - you need a decent flexible drive to attach to your meaty mains drill. Not expensive but get a good one as mine ran its bea...
... rotor are flat together.
Another way it to put the car up a hoist and let the car spin the wheels in drive (idling)to make sure they run straight on the car....
...nnections? Those might need resoldering. . . You might need new relays.. You might check into horizontal drive transformers - There are so many things that might be the cause.......
... something out of it in the process. So let me ask you this. Is there any way to get the memory the hard drive and the wifi card out of the laptop and out it into the pc? And I have one last question ...
...he inside. 4 cyl. automatic trany. i would say it is in fair to good condition, i am getting to old to drive it anymore and want to sell it to a family member. without going through all the posts c...
I read your post and many others that were similar but nothing worked until I finally removed the disk drive motor. It had D/V3.0 on its label, so I assumed 3Vdc operation and tried that. Spun very ...
...per dies while I am driving. I had the fuel filter replaced and it died the next morning. I am scared to drive it. A mechcanic tested the fuel pump and said it was spiking at 100 and I need a new fuel...
hey, there is a '.rm 'file on ma 'e:' drive ...whenever i m trying to delete the file, computer tells dat file is being used by other processes....can u help me out how to delete ...
...
SEND ME YOUR E-MAIL ADDRESS LET SEE IF I CAN SEND IT TO YOU.
I THINK YOU HAVE A 700-R4 IF REAL WHEEL DRIVE THAT IS.
LOTS OF PHOTOS FORD CHEVY 1988 1998...
...ut by the sounds of if if you'd want this car to serve you - I really wouldn't advise you to drive one more mile with it until a professional mechanic has looked at it (while pretending yo...
...ne. It there a pressure cutoff switch? Any help? It's starting to get warm outside and I can't drive in traffic when it does this....
...b the tool repeatedly in the same direction over a strong magnet. A good source for these is an old hard drive. Take it apart with Torx drivers, and you will find some great magnets (with a coil betwe...
... available from places like Grainger. They are often retained by set suddenly screw secured collars or drive pulleys (cheaper units) Presently or the frame of the unit. They can be ordered by shaft...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...