engine
check out car-part.com
it's a boneyard search engine and there are some really good prices out there.
Did you check the CV joints.
Does the speedo do anything if the car is in gear and engine running?
the same happened to us and we had to get a new float. it cost us 6.00 at a small engine repair shop. problem solved
remove a transmission on a hyundai accent 2003
Does the engine need to be removed with it?
...xture screw) close it by rotating clockwise until you feel it seat, then back it out 1.5 turns
Let the engine run for 5 minutes then move the throttle to FAST then turn the power adjusting screw cl...
any suggestions on the best company to by a remanufactured engine on a 1998 astro?
thanks,
mark
if the starter just clicks, try turning the engine by hand, if it turns, try jumping it again, and let it boost for about 5 min before trying to start it.
...LEMS INSIDE TANK.
TO CHECK IGNITION MODDULE TEST HOOK A TEST SPARK PLUG ANY PLUG WILL DO LAY ON TOP OF ENGINE CRANK OVER SHOULD HAVE A BRIGHT BLUE SPARK WITH A GOOD SNAP TO THE ARC.IF YELLOW OR WEA...
ignition timming for a 1999 ram 1500 5.2 engine code y
...y / intake manifold. Is there a sealer that I should be using?
Intake gasket failure was the cause of my engine failure and I want to be dang sure this intake gasket is sealed without damaging the ga...
I would replace the engine Temp sensor, it could be reading wrong. They are cheap, about $15 each, there are two.
Hi Guys have to change the clutch on the Honda HT-3810 with the G400 engine.
As I never work on this need some advices on how to do it.
Thanks
worked fine got a rag caught in the auger and it stopped the engine will not start now how much damage is done and what do i look for
...ere is some anomaly in the fuel injection system. I adamantly have never used such a product on a petrol engine though. To that degree nevertheless I`ve had good results on one or two older diewsel...
...either way???
i added plain oil treatment not motor oil. drove my olds 186,000 miles no codes no check engine lights nothing sold car still running around town no it will not go into limb mode. tra...
...like your throttle is sticking and when you put it into 'park' you are removing the load of the engine....
...ne advise the way to properly set the hydraulic valve adjusters after reassembly of the Subaru EA81 Turbo engine?...
...is the worst. low compression from worn cylinders/rings.
Of course a lot of things a little wrong w/ the engine can cause this, most all of them aren't worth fixing (given the vintage)
Did yo...
drain for the water is the rad - best way.
engine blocks dont have drains other that frost plugs.
...e trouble started there seemed to have been problems with the connector or wire to the fuel injector. The engine would stall and only start to stop very soon with sputtering. I cleaned the connector a...
...rmonic balancer has slipped. Then again, there are better ways to establish true TDC when re-building an engine such as a positive piston stop. excessive knocking, a condition that one can usually...
...s or information on building a hydroplane, i am a novice so need something simple but that i can use with engine. thanks. please have a look at my profile for further info...
I have a 03 jetta with PO455 engine code. Changed gas cap no help. Any suggestions ?
sounds like either a faulty temp sensor for the fan or the relay. it should not run when the engine is turned off.
...t turn on your head lights low bean turn on your heater only not a/c blower on low trun on your radio.let engine warm up down to idle fore a second or two.then only long enough to see engine idle unde...
...oing down a long hill, or even if you're slowing down to get off an exit ramp, downshift and let the engine do the work so you don't overheat and warp the rotors. this works with automatic o...
If the timing belt breackes on a 325I 89 bmw is the engine good?
Probably a minor carburetor adjustment.
See the 'articles' section on "small engine carb cleaning and repair".
put some fuel into the sparkplug holes and crank the engine. does it start at all.do you have a compression tester.
First off i'm having troubkle locating it. I think it is on top of the engine. A3.4 litre buick rendevous. Second I am getting a code for low voltage in position two sensor. Can anyone help? Th...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...