engine
I restored an 85 with the Z24 engine and drove it for years - I'd like to get another actually.
If it is indeed the engine, you'll be happy to know that they are cheap and plentiful. If y...
...ell. If the pressure test passes, they will probably try putting the dye into the coolant and running the engine for a while. Afterwards, a black light will be played around the hose ends and such to ...
...GE IT EVERY 50.000
MILES LIKE BOOK RECOMMENDS.THAT WAY ISSUE IS OVER.IF YOU DO NOT YOU SIMPLY MAY DAMAGE ENGINE.REPLACEMENT 4.500 DOLLARS ENGINE, WHICH IS CHEAPER ????
TIMMING GEAR KIT SOUNDS GOOD...
If this is a 'horizontal' shaft engine, there should be square headed plug low on one of the sides of the engine. If a vertical shaft, it will be on the bottom of the engine.
2001dodge but what model (IE pick-up,van,) if its a car whats the model ???? if the rad is lower than the engine find the highest point that coolant flows @ the engine (usually @the thermostat on most...
...t a 23' Scottie Craft w/ cuddy cabin that sounds almost exactly like yours with the exception of the engine. Mine has an AQ170 gas engine in it with the 270 outdrive.
Right now I have the d...
engine temp sensor detects coolant temp and adjust fuel accordingly.thermostat might not bringing engine to the correct temp.wires and ignition module will cause skip.engine driven by a senior person ...
I have an evinrude 4V outbaord engine I need help cutting it on,
The engine is turning(spinning) when the key is in the on position but the engine is not cutting on, I don't know what to do!!
...red to get the diesel to self-ignite and therefor sustain combustion are far in excess of what a gasoline engine is designed for. Also, the bearings in a gas motor are very fragile compared to those i...
...uslly not advisable to drive, but I had to push it for about 20 miles. We think it`s in the front of the engine.
To take off the oil pan on this engine you have to undo the engiune mouynts and j...
.... (of course they're $40-80...) and that will tell you right away. but barring that, listen to the engine while it's running. If you have a significant vacuum leak, you will hear a low hi...
A friuend of mine has just had a major engine failure of her 97 cad due to apparent headbolt loosening. They had to remove the engine & apparently put some kind of thread devices like helicoils ...
so the electric start does not turn the engine just grinds the starter gear. sounds like the engine is seized.
I am working on an OMC (GM) 3.0L (same engine as a Chevy II 2.5L L4)
Just had the pistons hung with new pistons and new wrist pins. Two of the rods seem to swing very easily, and the other two have...
Hi Guys,
I was just doing some checks on my car, a 1992 Ford Laser GL, when I realised that the Engine Oil was very low. So I quickly drove to my nearest 7-11 shop and got what I first thaught was En...
Need more info.
Year, engine....you wrote "injector" (singular) so I assume it's a TBI engine ?
IF THIS IS A FORD THE GUAGES READ HIGH AT IDLE. ALONG IT DOES NOT GO IN THE RED. COOLANT ENGINE TEMP SENSOR DIFFERENT FROM GUAGE SENSOR.IT MAY BE OUT OF CALBRATIONS OR INCORRECT.
AGAIN PEOPLE POSTING...
...ours 1kg lpg=2liters) lpg at just about full load 14amps at 220volts.WHat is the mechanical output of the engine (kwatts and or hp)and at what Rpm should engine turn to output 50/60 hz.?
Question2&...
I have seen this problem with Saturns before. The most likely issue is that a part called the ECTS or Engine Coolant Temperature Sensor is faulty.
In older mechanical cars, there was a choke to re...
SHOULD I BUY ANOTHER CADILLAC? SINCE ALL HAVE THE NORTHSTAR ENGINE AND THEY ARE CONSIDERED A THROW AWAY ENGINE?
... and filter in my vehicle. After starting up the vehicle, I heard a swiching pulsing sound. I stopped the engine after maybe 30 seconds of hearing the noise. I then looked under the engine and saw the...
Hi, the air filter should be on the right side of the engine and right as if walking behind, it should be the thing sticking out the farthest on the engine.
you have to remove exhaust clamp where header pipe plugs in converter.the two dog bones bars on top of engine hold engine to front frame has to be unbolted from engine end theirs two smaller holes in ...
I recently replaced my plugs and wires on my car. Three days ago i was driving on the freeway and the engine started to skip and the check engine light went on, i hooked it up to a OBDII scanner and c...
I just rebuilt carburator and engine works fine but when I blow snow the engine wants to cut out. Its probably the govenor. What can I do?
...ly receive your reply. Others would usually agree it is as you tell, I should have had a justly seized engine during that first run, probably.
Is the fact that the engine fuel consumption as s...
it hasn't got immobiliser, or check engine light. yes have changed all the above parts. i have also checked and re-wired all of the engine earths. this car is really annoying me.
I have a 1988 Chevrolet Celebrity with a V-6 2.8L engine and there is no spark in the engine. I was told that it could be the crankshaft postion sensor but not sure b.c i cant find it...can someone he...
...n:
Most importantly, the last few pages in 692509.pdf contain cross-reference
between Sears Craftsman engine part number and Tecumseh engine model number!...
can you please post the model numbers off of the engine so i can look it up. or take the old starter to a small engine repair shop and have them order a new one.
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...