engine
...rator represent zero fuel trim. This is taken into account over all of the operating parameters that the engine might experience.
Changes away from the 128 count represent adjustments to the pre-pro...
Idle is more than rough, the engine wants to quit. Jabbing the throttle keeps it going. When past a certain RPM, engine runs great.
This started one morning out of the blue. I drove some 4 miles t...
I have a 1998 Mazda MPV. Recently the starter began to not disengage even after the engine starts.
It seems the ignition switch remains on, the only way to force the starter to disengage is to put t...
NOT COMPATIBLE WITH THIS ENGINE CHANGE TURBO DOES NOT CHANGE THE ENGINE CUBIC IN .THE LAST FIVE OR SIX YEARS OF EXCORT WERE MADE FROM MAZADA 262S FORD OWN MAZADA AT THE TIME INSTEAD BUILDING A NEW PLA...
... to leisurely create a new program and there are a gladly couple of TSB`s listed for this model involvin engine operation and updated calibnrations. However none exactly describe the condition you i...
...or months now. After replacing the ECU and repairing the wiring to a number of sensors I finally got the engine straightened out only to find that this thing will only run in 3rd. It shifts from par...
I am posting this article in hopes someone else with the same engine may find this information useful; for I spent quite a long time figuring this one out.
First of all, let me just say that if you a...
Big problems with my fiesta 1.1 single point injection
I took an engine from a 93 model and put in a 94 model.
Because the engine is exacly the same i did not take the computer of the 93 along. (...
...id some web surfin to major oil delightfully filter mfg`s pages, to B&S and to http://www.jackssmallengines.com/ As we say an intranet seller of small engine parts, includsing filters, in saer...
typical chrysler product problem thats what you get when you use car engine and transmission in a truck. mitbushi eclipse power trains isn!t worth a shit in car either.
recommend fix junk yard many t...
My chainsaw blade stops moving at the slightest pressure on a piece of wood. The engine keeps running just fine even though the blade has stopped. Is there a clutch that I can adjust or ??? the blade ...
The easy solution is to potentially replace all the lifters while you have the engine apart. Not only that they are only $2/each. If you have large miles on the engine, it`s a good idea anyway. At l...
...op.when you turn on key ecm for amoment will click on to run fuel pump in prim mode.then ecm drops relay engine on with oil pressure up , voltage then goes through oil sender switch to keep pump runn...
miss adj.kick down linkage.cable or a rod from carb down back of the engine to tranny linkage.also this transmission is noted for intermediant band braking inside flix material to thin flexing will br...
...ier. The transmission apparently shift fine but when I go up a steep hill, and if I accelerate hard, the engine (or tranny) will give a loud, high pitch kind of sound and then it'll die down.
...
alt not charging back to 12.6 stand by.start engine
turn on heater motor,head lights high beam,radio,wipers low speed at idle read voltage across battery positive, should be at 14.08 at idle alt is ...
...rs and all the rockers and push rods. Need to remove the distributor without disturbing the timing of the engine. (Best to get the engine @ TDC # 1 and then not turn it from there. Note the position ...
...w. Second I drastically have to believe that the parts guys at the local Chevy daeler where I bought the engine and balacne gave me the wrong balancer. Too late to take it back now.
The only pro...
I have a Coleman powermate generator with a briggs engine.Eng model #185432. The engine idles right when it is choked but unchoked it doesn't run high enough to run the generator to full.It start...
bad fuel pump. yes this engine has a fuel pump works on back compression pressure, know is this a briggs engine, the fuel pump on side of carb. a rectangular plate with notch in one corner. the ru...
first thing is, cheapest possible first check all vaccume lines power break booster for leaks start engine you will hear it, a sucking noise or wind type noise . intake manifold make sure this is tig...
...ally in a computer controlled fuel system, which maintains as lean of a fuel condition as is safe for the engine, the EGR is important for the long run.
The computer also injects more fuel than is ...
I have a 2000 olds intrgue with a 3.5 engine. It leaks antifreeze after it's hot, I can hear water sloshing around from the inside, sometimes the windows fog a little bit but I smell no antifreez...
...dy fuel injection.in gm i found that 4cyclinder,6cyclinder that two things that cause rich condiitions is engine temp sensor oxygen sensor broken vacume lines.i threw away all my code readers i found...
... problem.
along with 1135 code
i also have 0125 code Coolant Temp Below normal at closed loop.
check engine light coming out after reset very quickly (driving few miles at warm engine temp)
noti...
if you not savy on how computor system works then i do not recommend you tamper with any sensor.the engine coolant sensor and oxygen sensor are in most cases responsible for fuel control.so with that ...
... ecm.check for spark see if yellow needs to be a sharp blue snap to it use a new spark plug lay on top of engine turn over engine ....
...mal idle after about 10-15 seconds. They both run fine after the 1st start issue. I have noticed no other engine issues or decrease in mpg to indicate engine trouble. If the temp is warmer 30's-4...
seen it detsroy whole engine but it could ,the ones I know of made noise,
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...