engine
I have a '99 Ford Taurus with a 3.0L V6 OHV engine. We had coolant in our oil and decided to trade out the old engine with a reman'd short block and reman'd heads. After removing the o...
alt not charging back to 12.6 stand by.start engine
turn on heater motor,head lights high beam,radio,wipers low speed at idle read voltage across battery positive, should be at 14.08 at idle alt is ...
...mal idle after about 10-15 seconds. They both run fine after the 1st start issue. I have noticed no other engine issues or decrease in mpg to indicate engine trouble. If the temp is warmer 30's-4...
...eel clutch, throw out bearing ,pressure plate, you might have to change cv joints ???.you need to support engine to remove lower engine cradle to remove the tranny why did buy this model would been wi...
... trans. At one point while driving it home (long drive) I got a hard shift from time to time and a check engine light. I added some Lucas trans fluid and the problem seemed to get better, but near h...
...tom: Can't pull the starter cord at all. Problem: clutch center is threaded on, and locks against engine sideplate when the engine tries to rotate, locking up the engine. It seems to only fit...
...valier The altermator is making a high pich sound (you have to put you ear up to it to hear it) after the engine is turned off. After pulling the relays, breakers, and fuses, it stoped when the PCM fu...
Does anyone know of a safety switch related to the auger belt that may keep the engine from starting or stalling?
A mechanic insists my problem with starting an Ariens Snow Blower was somehow related...
throttle position sensor air intake part of your gas peddle assembly on top of engine.how ever is this a code read out or what.rough idle usally is a vaccum leak.or bad wires, or pluges,defective igni...
inside distributor have to remove from engine.drive out shear pin on gear at bottom pull up and out on whole shaft from top module mounted under rotor plate will not come out no other way. also before...
should be ok 3/8 socket and drives. buy the way what engine i might have shop manual 1.3 or 2.3 or what.
...tion: dirt. heat, excessive at plowing and harvest, cold winters.
to maintain oil condition also extend engine life.
remember hotter the oil the thinner it gets lower oil pressure.
i personnelly...
There should be a relay in the main fuse box or in the engine bay somewhere.
How does one get in around the back of the engine?
UP ON ENGINE ON FUEL RAIL TO THE INJECTORS UNDER COVERING. NEAR REGULATOR THEIRS A FUEL NIPPLE PLASTIC SCREW ON COVER.LIKE A/C NIPPLE BLK I THINK IT IS ON PASS SIDE BACK CORNERTWO FUEL LINES COME UP F...
...ervously start and had wet plugs. Once again after squirting oil into the spark plug holes, winding the engine over a few times, I notiecd that the fuel kept pouyring into the throttle body. After ...
Hello Danny.Lee - welcome to the forum I am happy you joined us.
Couldn't it be the engine and that it needs replacement?
if your engine is making oil show some kind of leak.a head gasket is leaking coolant in the oil.compression test should detect this or a cracked head.or even a problem with the block.you do not just c...
...15-20 minutes after it dies check the coil.
Coils stop working when they get hot.
You will need the engines model number and serial number. If its a Brigg and Stratton motor of other make. You w...
I don't believe it. After looking at more postings, apparently there is an engine additive called "Steel Seal". Something you pour in your engine to supposedly seal a leaking head gaske...
Hi
You can use a 11x13 two blade. I have that on my own engine.:
Bank one is the cylinder bank that houses cylinder #1
Bank two is any -other- bank the engine might have (as would be the case in a "V" type engine)
The 4.3 liter engine in your S-10 u...
can someone tell me when the timing belt breaks on this engine how do you line up the cams and the crank with no marks thanks
check engine and tranny mounts.
if they are loose or bad, it will make a clunking noise.
Sure sounds electrical to me. Bad cam or crank position sensor, bad engine control module, that kind of thing.
where do i put freon in the 3.4 engine
See the 'articles' section for "small engine carburetor cleaning and repair".
I don't believe it. After looking at more postings, apparently there is an engine additive called "Steel Seal". Something you pour in your engine to supposedly seal a leaking head ga...
...s or information on building a hydroplane, i am a novice so need something simple but that i can use with engine. thanks. please have a look at my profile for further info...
...ager are the two biggest abortions on the road .of course its the tranny.alway is and alway will be.
the engine and tranny are mitsubishi eclipse car power trains.it has all it can do to work in a ca...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...