floor
...fter into gears, although the car will not go into gear, when pressed the clutch goes all the way to the floor, all the fluids levels are checked and rechecked. Any ideas would be a great help....
... was still working. a Brentwood 125,000 BTU 35 years old when on would run a long time and even get the floor registers so hot you could hardly touch em. My new furnace is constantly kicking on and o...
I just tried Quick Shine Floor Finish made by Holloway House. I purchased it at our local supermarket. I used a paint brush to also apply it inside the bin in hard to reach places. Several coats is go...
...ly through unchallenged by furniture, carpet or any other normal buffer when they are installed near the floor.
Thanks,
RH...
... heater fires the pressure rises to 150 PSI and the pressure release valve opens and water leaks onto my floor. I do have an expansion tank, but I guess it is no longer working. How do I test/calibr...
...e "eyes" that prevent the door from closing when someone is under the door (installed near the floor on either side of the garage door). I've had leaves interfere with my opener - so ma...
...e Dryer is 7704 and Washer is WM200. Recently the washer stopped spinning and is spilling water on the floor. Our repair tech told us over the phone that it is the motor. A replacement motor onlin...
..., started and absolutely shut off again. Finally from there gently started the car with throttle to the floor. Cold start solenoid was the problem. Your car has an eqiuvalent system for cold starts....
...039;ve got a basement window that is busted out. On the outside, it is blocked almost completely by the floor joist of a deck. On the inside it's blocked 3/4 by the back of a sauna, although th...
...'t think we have the skills to tear out and rebuild the wall. Is there a way to build some kind of floor support instead of screwing it to the wall?
Thank you again....
....
Laundry: You will have to give access into your apartment, or you could add a stacker to the second floor
Heating/cooling: Do you currently have zoned heating/coling? If not, the upstaitrs m...
...door opener has a safety laser 'eye' (usually mounted down at the bottom of the railing by the floor) which "sees" something blocking the closing of the door (like an elevator door...
... except they are not made as a retrofit item. I have seen various rubber dams that can be sealed to the floor. My only issue with these are:
(1) For the water heater I would like to have a drain th...
... for about two weeks. Now I can only apply very light gas and it takes too long to get up to 30mph. If I floor the gas pedal the motor sputters and backfires for a while and then guns the car forward....
...he water that overflows seems to be high in minerals because once dry, there are powdery deposits on the floor. They told me to "wait a few days" & watch for leakage again. Any ideas?...
...f the switches for a ceiling fan. Third switch could be half of a duplex outlet for use with a table or floor lamp for when you come into the room. Normally power comes in at the switch. If nothing...
...side disturbingly wall, the vapuor barrier only goes down to the top of the shower base and not to the floor as it should. Moreover I am not sure how to rectify this since I cannot take the base ou...
Have 2 hydraulic floor jacks made in China. The jacks have a creepage problem (when the release screw is in tightly the jack still comes down).
One of the release screws is badly bent and the other...
.... I also adjusted (bent down) an inlet control lever ever so slightly to sit flush with the carb chamber floor, just as it is supposed to. But afterwards the idle performance was actually worse, and n...
...unnel rails that are open underneath. i would like to take sheet aluminum and connect the gunnels to the floor for more rigidity. next i want to build a center console. i do alot of catfishing and the...
...e the problem, making more negative pressure in the room !
How about a Toilet that's close, or a Floor Drain that the trap has dried up on, or occasionally dry, maybe it's sucking in some...
...a pickel forks to remove tie rod ends and lower ball joint. a good pry bar about 10 feet long and a good floor jack to put under tranny makes it easier to lower down.i not sure but their may be a k fr...
... lot ourselves, including the plumbing, electical work, heat, and other stuff. We installed hydronic in floor heating with a high efficiency HW heater as the heat source. This is a propane fired uni...
...st concern is the brick. The house is a ranch style with a half basement. The exterior walls of the main floor are brick from the ground up about four feet. The rest is permanent aluminum siding. The ...
...ng even removing the dip tube from the water heater and tested the water pressure.this house is only one floor so all the piping is visable in the basement.it all loooks pretty normal to me,there are ...
... but from the areas I could get to (due to my expanded waistline, I couldn't inspect all of the sub-floor area I could 2 years ago!!) I couldn't see any surface water. Are the any obvious si...
...couple of years) and you are going down a grade, you may find that your brakes all of a sudden go to the floor because you have boiled some fluid - DOT 3 (what most people use) Ford fluid boils at 290...
...Proof) For the time being can be used to prevent water from fortcing up through a new concrete basement floor.
Make sure that you conect the weeping tile/socially drain tile mentioned into a sump...
Hi there,
I am new to this forum, a new DIYer and definitely would like to learn more about DIY tips for my home. I was wondering if anybody here could help me figure out the right laser leveler fo...
...er off to the fridge. There should be a saddle valve to do that with some where on your plumbing in your floor joists or behind the fridge. Unplug the fridge. On Maytag's the freezer temp control...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...