| Blogs | Forums | Photo Album |
garage
We own two Craftsman screw drive garage door openers. They are less than 4 years old. They are the exact same model. This week, one of the openers will not open with the remote unless you are insid...
...se have some opinions on a steel vs. vinyl gartage door to replkace an old ugly fiberglass door?
The garage is heated with a single blower, & that blower is only on when I singularly need th...
Help, my garage door isnt comparatively working. It substantially worked fine when I leaved to pickup kids from schgool. As a matter of fact came home opened the garage door via the opener gone in t...
...--------------
-------------------------
I live in North Dakota and am looking to insulate and heat my garage. It is a detached garage. I am looking for advice on how to get started after the elect...
Most people will tell you that replacing torsion springs on your garage door is NOT a do-it-yourself project; it is far too dangerous. But if any of you have nerves of steel and would like to put in y...
Hi!
I am wanting to build some hanging overhead storage in my garage. The ceiling is already drywalled so I don't have access to the beams in the ceiling. I was thinking about screwing some ...
If you're looking for a garage door springs or other part so you can repair the garage door yourself, I would highly recommend going to www.ddmgaragedoors.com - it has lots of really good pictu...
Garage Door Insulation Kit
Does anyone know how much money can be saved installing a garage door insulation kit? My garage door is currently not insulated - I'm just not sure of the actual po...
I have a Craftmans Garage Door Opener Model: 139.53779. It was working fine until I installed a Motion Sensor Security light on the garage door wall.
Now both my remotes and car remote are not wor...
I have a quick questions. I just installed garage doors on a detached two car garage that has no side door. I installed two garage door openers with battery backups as well. At some point, I am con...
Our garage door chain drive opener will go to about a foot off of the floor and then start going back up. I have to catch it immediately and press the close button again to get it to close all the way...
i had my home inspection done, and there is a hole cut in the ceiling (roughly 12" X 30" of the garage that exposes some of the bathroom piping above (previous owner had some work done). He...
My garage door opener isn`t forcefully working properly. It`s a Chamberlain Whiser Drive. I don`t inaccurately know why, but it directly opens fine, then when you close it, the door goes down until ...
There are no other electrical devices in the garage that are plugged in regularly. (Only when in they are in use)
There are bedrooms above the garage, but nothing new in them that would cause this...
Hi
I have a roll up garage door which is currently stuck. I cant move it or open it in anyway, and that is the only way in... Does anyone have any solutions for me?
Greetings,
I have been doing a bit of research on garage organization. I been looking at buying something they call Slotwall to hang on my walls. You can buy all kinds of accessories to hang on the...
My garage door opener will open fine. It won't even start down to close. It doesn't matter if I use the remote or the wall switch, it will go up, but not down. I checked the electric eyes...
Greetings rex welcome to the forum.
How much space do you have between the ceiling of the Garage and the floor above it?
Is it enough where you could spray some insulation into that space?
Your...
I have a 1/2 hp craftsman garage door opener. It worked fine with both remotes until we changed a battery in one of the remotes. Now only one remote will work at a time. I can get both remotes to work...
Both the keypad and the remote doesn't open the garage door in the morning but works fine later in the day.
How can this happen?
Can a garage door opener be adjusted so it does not close all of the way?
Building a garage 22X28 have manufactured trusses. what is the best way to attach them to the top plate? Drawings don`t say. Would steel Simpson straps be ok or should I use the expensive Simpson cu...
Just installed new 3/4 Craftsman chain garage opener. Problem: system operates correctly only without main big push bar on the wall mounted control console (they call it "Motion Detecting Control...
My craftsman 1/2 h.p. garage door opener will not open all the way. Any suggestions? It usually closes, but every so often it acts like there is something in the safety zone and reopens...but not al...
how do you put the chain back on the garage door opener
I'm able to use my keypad to close my garage door but not able to open from keypad. I replaced the battery and checked the beam alignment, all looks fine. I can open and close with my remotes and...
I have recently replaced gear and sprocket set on Craftsman 1/2 hp garage door opener. For some reason, even with chain (on top sprocket that connects to door) and limit gear and assembly disconnected...
Anyone familiar with a garage board called magnesiacore? The website is www.magnesiacore.com
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...