| Blogs | Forums | Photo Album |
garage
Can a garage door opener be adjusted so it does not close all of the way?
I have a craftsman garage door opener and using a keypad opener with it. Today the keypad quit working so I replace the battery with no help. The door works fine with a wired wall button and with the ...
Just installed new 3/4 Craftsman chain garage opener. Problem: system operates correctly only without main big push bar on the wall mounted control console (they call it "Motion Detecting Control...
My garage door opener jerks or jumps when opened. I checked the spring tension and it is about neutral. When the door is disengaged from the opener, it lifts easily and does not bind anywhere. Any ...
Four days ago I spread some Quickrete resurfacing cement over the pitted parts of my garage floor. The bag of mix was 5 years old and could not be poured and came out in chunks.
I could barely ma...
My craftsman 1/2 h.p. garage door opener will not open all the way. Any suggestions? It usually closes, but every so often it acts like there is something in the safety zone and reopens...but not al...
Building a garage 22X28 have manufactured trusses. what is the best way to attach them to the top plate? Drawings don`t say. Would steel Simpson straps be ok or should I use the expensive Simpson cu...
I cannot for the life of me see how the keypad was mounted to the outside of the garage.i need to remove it.....i know it can;t be difficult yet I haven;t figured it out...........any help? thnx in ad...
my garage door is hard to open. The cables are not broken and the springs I cant see the spring is a torquemaster what is the problem
Craftsman 1/2 hp garage door opener problem
I've replaced the sproket assembly in my 1/2 hp Craftsman chain drive opener and now the unit will only runfor about two seconds one directionand the...
First, use WD40 on the bearings in the rolers to free them up. Then, use a light weight oil like three in one oil, to oil the bearings.
Do the same thin for the roller stems that go in to the hin...
...my old car`s engine, I didn`t see much of other car mechasnics, and expertly have not had practice in a garage. I drove my new car to the dealer for maintenance. Apparently it is a Mitsubishi Spac...
I have recently replaced gear and sprocket set on Craftsman 1/2 hp garage door opener. For some reason, even with chain (on top sprocket that connects to door) and limit gear and assembly disconnected...
I have a Craftmans Garage Door Opener Model: 139.53960. It was working fine until yesterday. When I try to close it is not closing, But the light bulb is blinking 10 times.
I checked the motion senso...
...ff our upper living area. It has no ventilation if I insulate and dry wall. Can I put vents in ceiling to garage space instead outside? Or is there something else I could try?...
does anyone have any idea about garage door openers? It seems mine is going halfway down and then stops....the chain has to have come undone at some point...any idea how to fix this problem?
Thanks for looking, hope some helpful advice will follow my plea.....!!
I have just errected my wooden garage, 16foot by 9foot.... Im going to be using as my office/workshop for my clothing company...
I just installed a Craftsman 3/4 HP garage door opener. When I press the opener button on the wall switch with the door closed, the opener tries to close the door, rather than open it.
What can I do ...
... is the gears are not close enough together. There are adjustment screws on the side and the back of the garage door opener but I don't believe they would impact this adjustment. It did appear ...
The overhead light of our Craftsman garage door opener #139.53985D goes off after the door opens all the way (like the power is off). The light must be on in order for the door to work properly. The...
Hi,
We have a garage wall and behind the wall is our bathroom. I removed the sheetrock from the garage wall (wall which has bathroom on the other side) as I wanted to see if there was a water leak...
I have a Craftsman 1/2 hp garage door opener with a remote keyless entry and a remote opener in the car. I recently replace the batteries in both. Now neither work in the morning but work in the eve...
after 20 years, I had to replace the cable of our garage door opener, because it finally snapped. I bought a cable and a repalcment connecting link from sears, and after one day the link snapped open....
I have an old Craftsman garage door opener that just quit working - model 139.53627SRT - manufacture date 6/95. It hums for a couple seconds when I hit the button but thats it - no movement at all. Th...
Hi Beeachard, welcome to the forum You can lift the rails of your garage door and that should solve the problem
i am looking for a seismic detail for a existing soft story garage opening, that connects to a typical one story residental house in san francisco, calif.
I doubt that your garage door opener is a vampire. sun has nothing to do with that, but heat. the wall mounted control console made of plastic. big push-bar is also plastic and as I realized they desi...
My garage door will go up with the remote but it will not go down. You have to hold your finger on the inside mechanism until it goes all the way down. It's a new remote from Sears. What could...
My garage door opener will open fine. It won't even start down to close. It doesn't matter if I use the remote or the wall switch, it will go up, but not down. I checked the electric eyes...
Help. My 1997 vintage 1/2 HP Sears Craftsman Garage Opener needs a sprocket assembly change. I have removed the outer casing and can see the shreds of the plastic sprocket and know i need to replace i...
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...