garage
My garage door (craftmans) key pad doesn't work in cold weather. I've changed the 9v battery. I've taken off the wall from outside & brought inside for a while to warm up & it w...
does the capacitor to start motor go bad in craftsman garage door openers if unused for a couple of years?
Have a Chamberlain 1/2-HP chain drive garage door opener. Door will now will operate in only one direction. Removed motor panel to observe up/down limit switches. When activated, the motor will run...
...n problem. This is what I did...
I loosened the pulley assembly that mounts on the wall just above the garage door. This gave me the needed play to get the belt around the entire track... Then, on...
My garage door opener'd drive gear keeps getting destroyed/eaten away. I replaced and have the same issue..Went through a gear within 2 months. What could be casuing this?
My craftsman garage door stopped working through the remotes. It only works through the push button on the wall. The batteries are fine. What is the problem?
I have an old Craftsman garage door opener that just quit working - model 139.53627SRT - manufacture date 6/95. It hums for a couple seconds when I hit the button but thats it - no movement at all. Th...
my garage door is hard to open. The cables are not broken and the springs I cant see the spring is a torquemaster what is the problem
My garage door opener initially was closing and once touched the ground it was bouncing back open. After I attempted to adjust the up/down trigger, now it only opens few inches and stops. Any idea how...
Hi, I have 2 Craftsman 1/2 HP Garage door openers.
We have tried to instal them but none of them work after strengthen the chain.
The installer told me that it has to do with the cycle. In my coun...
My garage door will go up with the remote but it will not go down. You have to hold your finger on the inside mechanism until it goes all the way down. It's a new remote from Sears. What could...
does anyone have any idea about garage door openers? It seems mine is going halfway down and then stops....the chain has to have come undone at some point...any idea how to fix this problem?
my craftsman garage remote will not let door up..all remotes let door down..i cleared all programs,reset all remote.remotes let door up and down,after a few hours remote will not let door up...PLEASE ...
...djust them in the winter you usually go counterclockwise but it will be in your manual this will fix your garage door....
I have a 1/2 hp craftsman garage door opener. It worked fine with both remotes until we changed a battery in one of the remotes. Now only one remote will work at a time. I can get both remotes to work...
Both the keypad and the remote doesn't open the garage door in the morning but works fine later in the day.
How can this happen?
replaced all the outlets and switches (2 switches). the house was a HUD and all the wiring for the garage was disconnected. anyway, when i turned the power back on everything seemed to be okay. i plug...
Hi Beeachard, welcome to the forum You can lift the rails of your garage door and that should solve the problem
I have a Craftsman 1/2 hp garage door opener with a remote keyless entry and a remote opener in the car. I recently replace the batteries in both. Now neither work in the morning but work in the eve...
Does anyone know where I can find a IPB for a Craftsman 1/2 HP Garage Door Opener, Part # 11A5483-2 MFG 09/02.
The Gear that turns the chain broke, actually the shaft, that holds the gear, that tu...
Thanks for looking, hope some helpful advice will follow my plea.....!!
I have just errected my wooden garage, 16foot by 9foot.... Im going to be using as my office/workshop for my clothing company...
I doubt that your garage door opener is a vampire. sun has nothing to do with that, but heat. the wall mounted control console made of plastic. big push-bar is also plastic and as I realized they desi...
Four days ago I spread some Quickrete resurfacing cement over the pitted parts of my garage floor. The bag of mix was 5 years old and could not be poured and came out in chunks.
I could barely ma...
...ff our upper living area. It has no ventilation if I insulate and dry wall. Can I put vents in ceiling to garage space instead outside? Or is there something else I could try?...
I have a 1/2hp Craftsman Garage Door opener that suddenly stopped working. The motor sounds fine (even has a different noise when theoretically going forward and reverse which I noticed when it was w...
...#039;t let you close the door except by overriding (holding down the button manually).
virtually every garage door opener has a safety laser 'eye' (usually mounted down at the bottom of t...
My garage door opener will open fine. It won't even start down to close. It doesn't matter if I use the remote or the wall switch, it will go up, but not down. I checked the electric eyes...
... is the gears are not close enough together. There are adjustment screws on the side and the back of the garage door opener but I don't believe they would impact this adjustment. It did appear ...
Help. My 1997 vintage 1/2 HP Sears Craftsman Garage Opener needs a sprocket assembly change. I have removed the outer casing and can see the shreds of the plastic sprocket and know i need to replace i...
i am looking for a seismic detail for a existing soft story garage opening, that connects to a typical one story residental house in san francisco, calif.
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...