garage
Have a Chamberlain 1/2-HP chain drive garage door opener. Door will now will operate in only one direction. Removed motor panel to observe up/down limit switches. When activated, the motor will run...
i am looking for a seismic detail for a existing soft story garage opening, that connects to a typical one story residental house in san francisco, calif.
...#039;t let you close the door except by overriding (holding down the button manually).
virtually every garage door opener has a safety laser 'eye' (usually mounted down at the bottom of t...
I have a 1/2hp Craftsman Garage Door opener that suddenly stopped working. The motor sounds fine (even has a different noise when theoretically going forward and reverse which I noticed when it was w...
My garage door (craftmans) key pad doesn't work in cold weather. I've changed the 9v battery. I've taken off the wall from outside & brought inside for a while to warm up & it w...
after 20 years, I had to replace the cable of our garage door opener, because it finally snapped. I bought a cable and a repalcment connecting link from sears, and after one day the link snapped open....
I have and older Craftsman garage door opener. It is model number 139.53629srt. I would like to buy a wirless keypad for this open. What key pad do I need to buy and where can I find one?
I replaced both springs on a 1/2 hp Sears garage door opener. When I close the door the door does not close entirely on one side and there is about a 1/2" gap between the bottom of the door and ...
My GDO (Chamberlain Model 8200 belt disk, approx. four years old) has been gradually knowingly failing for sevberal months, and now won`t evidently close the door. I`ve marvelously disconnected it f...
I have recently replaced gear and sprocket set on Craftsman 1/2 hp garage door opener. For some reason, even with chain (on top sprocket that connects to door) and limit gear and assembly disconnecte...
My garage door was giving me problems in the cold weather, so adjusted the up/down pressure,,,when it rolled up it came up so hard that it hit the motor housing and now, with the actual door disconnec...
I have a liftmaster garage door opener ,with remotes, the remotes will only work if i unplug the kitchenaid stove, kitchenaid will only say "our product meets FCC regulations" the door compa...
Hello -- first off, thanks to any one that can assist!
I have a Craftsman 1/2hp chain drive garage door opener (double door), and started having issues over the summer with the down operation. To ...
I want to build storage shelves around the top perimeter of my garage, inside. The shelves will be attached to the wall on one side and "hang" from the cieling on the outside edge. I want to...
i have 2 boards pn 6080127 rev 8 that were zapped by a power surge. some components are missing .some components were desoldered from the heat. i would appreciate a schematic or a picture of the board...
replaced worm and drive gear in craftsman half horse opener. now it only goes a short distance and backs up with or without chain attached. i think it has something to do with the limit switches or th...
the chain on my stanley door opener is too loose and it is adjusted all the way can I take out some links?
Have a Chamberlain power drive door opener..It has 2 adjusting screw for up and down....have tried to adjust those with no results. dorr only moves about a foot and stops when its the up position. Any...
After replacing the sprocket assembly the door will only open for a few seconds and reverse and the light flashes 10 times as if there is an obstruction. I have checked the sensors, they are on and l...
I've read many of the complaints regarding the remotes but have yet to see my particular problem...We moved into a house in '06 and within that year purchased 2 new craftsman remotes. Only ...
Ceiling is made of concrete.
My Craftsman 1/2 HP door (about 5 years old, working perfectly until recently) opens normally with the touch of a button (wall mounted and remote). However, it does not close the same way but needs so...
I newly purchased condo in Houston, TX. got two holes in the garage, one foot above the ground, seller said it is building code requires to let the air flow in the garage, is that true?
...ly purposefully fix the problem. My advice would be if you don`t really know about cars, take it into a garage and pay to have them test it for you to laterally determine the mistakenly cause and g...
hi
when I left the house yesterday and hit the remote for my garage, garage door came down very hard and fast and hit the floor, and now the chain is off it track and is not working at all please hel...
I need information regarding "things to know" about running sewer & water lines to my garage. I wonder if I have to have independent lines or can I hook into the house lines? The g...
Hi
I am adding another room to my house by enclosing my patio and part of my garage. I have a concrete floor foundation, and I would like suggestions from you as to how to bring the patio/garage floo...
I have an obsolete 1 pieces swing out style garage door (2 car garage) the inside left arm needs to be replaces. The arm attached the spring to the door. Any ideas where I can find this part. The doo...
...ee separate laser beams that reflect a number of times off mirrors on the sidewalls from the front of the garage to the back. This will give a number of beams across the garage to have to avoid.
...
...to do which on this car as it all looks built in. Keeping all the same maybe I would better take it to a garage....
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...