We have a GE Space Maker Micro Wave (Model JVM-1640BB-001) that just quit heating this morning. Everything else (lights, turntable, buttons, etc.) works fine. It just will not heat. Any advice on what...
...hat were zapped by a power surge. some components are missing .some components were desoldered from the heat. i would appreciate a schematic or a picture of the board to figure out what is supposed to...
...s you can just loosen the joint and give a sharp hammer blow on the side of the unit tol loosen them. Heat can also help, even a cheap propane torch.
Dont funnily bring the nut off and bang on ...
It sounds like you probably live in a climate witch is cold in the winter & hot in the summer. If which is the case, I artificially recommend against a vinyl door. Vinyl expands & sarcastica...
.... " Did not help because I already have 3 bags of concrete bags tat have to to rock in the florida heat.. Thank you ....
The electricity in my kitchen, bathroom, washing machine, dishwasher, dryer and thermostat for heat are all out. the circuit breaker is fine. the odd thing is, when i moved into this house, i noticed ...
I've seen at dealerships many have water-based solvent tanks that they heat up and seem to work pretty well. It's literally a "dish-washer" that is used for general parts clean-up...
...ats the voltage reading at the coils. while it may be getting power there might not be enough for it to heat up. check the outlet its plugged into are you getting a full 240 volts(use a tester and be ...
...l problems. I have turned the oven double breaker off for awhile and then back on but still no element heat. The oven control panel works fine with no code errors. (Kenmore in-wall model 790)....
'freeze or heat" ... key thing is the OR. If temperature change makes it work, then you have a contact that is opening/closing based on expansion/contraction, aka a bad solder joint.
Pu...
My 20 year old side intake, gas powered furnace heats real well. However, when it cycles "off," a bang down the duct work is pretty loud. It sounds "far away." Then it is quiet....
Greetings mdunne welcome to the Forum.
Surely you're talking about those which heat a room.
Actually I've never seen any Wood Covers. I know those things aren't supposed to get a...
...crew terminals on the breakers and the offending recepticles. If they are loose, which is a function of heat generated by a loose connection that gets worse over time, can result in a tripped breaker ...
Hi
My Kenmore dryer only runs if its in the touch up position, and then drys on heat for a couple of minutes and switches the the cool cycle.
It won't work at all on the timed dry position, and...
Remove the battery. then take the covers off, and use a blow dryer (on no heat) to blow out everywhere. Get the battery out first though, even a little condensation internally can kill specific comp...
I installed 2 programmable thermostats - the downstairs one works but the upstairs one does not. Heat only system - only two wires - installed them exactly the same. Tried switching the control pane...
My 2o year old house has a Trion electronic air filter on the furnace (heat pump). My hunch is that these older units are not very effective and don't the air very well.
Anyone with experie...
...e and AC use the same squirrel cage but righ around time it started getting cold and I switched over to heat I noticed the blower was not kicking on..Well after fooling with it I found that if I get i...
The thermostat controls an electric valve that open and closes to let heat in or stop the water from moving though.
The base board does Stay hot for a while longer, but it could be that the valve is ...
..., and know absolutely if your Battery has Voltage or not.
This system you're using does what ?
Heat the Oil/Motor ?
Actually crank the Engine and let it run for 15 minutes, then shut it off ...
york furnace abut 12 yo, thermostat calls for heat, Hot serfaxe ignitors glows, flame lights in burner box for about 1 sec and then goes out, wont advance, keeps cycling same pattern. i already change...
...se connection some where.if you leave it running for a while does the color look ok.usually when things heat up they make better contact.does it look like just one color is off.could be loose conectio...
I have a Lennox Elite Heater and just out of the blue it doesnt heat up? I hear the fan kick on and I changed the batteries on thermostat, turned furnace, elec. off and tried to restart the furnace a...
... my pipes. I keep releaseing the air valves on both those places but the noise keeps going evertime the heat kicks on...
...ned the ignitors and reset their position. Start the furnace and it fires right up. Runs long enough to heat the house to warm and thermostst shuts it off. When it goes to restart 30 minutes later it ...
... know to much about the wood stoves but would like to buy a good stove that will last a long time. I am heating about 2200 sq ft and this is my main source of heat for the winter in western new york. ...
I HAVE AN OLD GE FURNACE AND I THINK MY FAN LIMIT SWITCH IS NOT WORKING, THE HEAT EXCHANGERS WANT LITE UNTILL I TAP THE FAN LIMIT UNIT, COULD THAT BE THE FAN LIMIT OR ANOTHER PROBLEM?
...a little, and you need to adjust it higher, which will hold the Blower Motor off, until it gains enough heat to run.
My best guess !
Have a good Day !
S.W....
... the most efficient lighting source there is. so the light you get for the power you put in is nuts. 0% heat loss. 100% happy electrons.
in other words, it's the light source with the least am...
...d a smoke stack. install some vents to allow air in. install some legs.make sure you paint it with high heat engine paint or BBQ paint....
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its
Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums
more posts...