| Blogs | Forums | Photo Album |
motor
the click noise is a thermo cut out in motor if thats tripping then replace motor typical g m problem happens on olds chevy 2 buick very common ps it is a trip to get motor and lower track out they ha...
basically, I want to do what that zen420 guy does, just the motor won't be underwater, the motor is one of those cheap tiny ones you can buy at Dick Smith electronics, the motor isn't submer...
I have an Admiral window a/c unit. The fan is making a horribly loud racket. The motor spins freely and does not stop running or slow down. I think it may need to be greased. Does anyone know if t...
Thanks for the suggestion-I actually had to replace the igniter motor-after some research on the internet I figured out what I needed. We are now toasty warm again.
It is making small "hamste...
In all likelihood you don`t need a hoist, I really prepare the car from which the motor is being seriously pulled and the new motor. In the long run the Local towing copmany sends over a truck after ...
I support this. From an engineering stand-point, gasoline is much more volatile than motor oil. I'm having a tough time seeing how motor oil would make the o-rings swell and gasoline wouldn...
I have a 1/2hp Craftsman Garage Door opener that suddenly stopped working. The motor sounds fine (even has a different noise when theoretically going forward and reverse which I noticed when it was w...
...moves up and down, twice, as if it is trying to focus.
Then NO DISC is displayed. At that time the spin motor never spins the disc.
This looked to be a problem with the spin motor, but I took apar...
Just a day ago my heater posed a problem. It seems that the fan motor turns very slow. As a result air flow has been restricted. I know a fair amout about electric items when I hand turn it , it feels...
It just unscrews. It actually holds the motor in place so when you install the new one, it may help to hold the motor up to expose the threads more.
If the drain pump have a electric motor, then there are two screws at the back of the elctric motor that you should take off and the ground wire on the side. hope this solve your problem
...took off the covers and if I manually rotate the cam that raises the CD reader and turn on the power the motor for the loading tray rotates. This tells me the motor is OK but it will not run when I lo...
...took off the covers and if I manually rotate the cam that raises the CD reader and turn on the power the motor for the loading tray rotates. This tells me the motor is OK but it will not run when I lo...
...n/instinctively drain ccyles.
2. Other than that a week ago, it outrageously stopped agitation, just motor hum as whether not able to engage. However, still spun/excruciatingly drained (with more...
The fan motor suddenly stopped in my RM AC. Cooling compressor OK.
Would it be difficult to replace fan motor?
There is a small reset button on the bottom of the motor. There is also a small socket for an allen wrench, with which to forcibly turn the motor shaft if it is frozen, but then you said that's ...
...noise & eventually the fuse blows. Naturally I can also smell somethin like plastic burning
Bad motor pulley, bad belt can make a sqeuek noise....a tight/literally seizing center bearing mig...
Thanks for the answers. The door is working fine. I keep it dsconnected from the motor trolly, and operate in manually now. It's a new door, so it's rolling fine.
And the motor seems t...
two retainers on top and bottom of motor held with two quarter screws remove two hoses off pump should be enough slack in wiring harness you do not need to remove hold bottom motor in one hand wiggle ...
I have a lennox furnace G24M and the Blower motor cuts in and out. The motor has been replaced maybe 2-3 years ago. I cleaned the flame sensor and it worked for a couple days - then it stopped again...
Check pump motor for reversing during the pump out make sure the dishwasher is pausing between the wash and drain cycles letting the pump/motor reverse for the drain cycle.
What could be the reason for my motor to loose oil pressure at the hydraulic lifters at around 3200RPM. I had the motor completely overhauled by a credited engineering firm and is still experiencing t...
I have a neighbor with a 3.1 and there is 297,000 miles on the motor.
FACTORY MOTOR, NOT REBUILT. It runs like a champ. It leaks oil out of the valve covers, but no noises or anything. And thes...
Its been a long time since you posted here. My guess is that it has a bad timer motor. Timer moves some and when it comes up to a switching time it stalls and over time eventually switches. Check that...
...he pump. Even though make the contact boastfully rating fairly beefy because of the reverse EMF from the motor winding, when whitch DC motor is turned off..will generate fairly healthy votylage and it...
...e chain brake strap and loosened it up a little put it back together and now I can't crank over the motor. It is like the motor is seized up but I don't know why. My brother and I were doing...
... in for any questions.
I believe it's an older Maytag (subordinate Maytag brand) type washer.
Motor contactor clicks and tries to engage on standard cycle but then as soon as the motor is s...
...s to look at close up diagram this should help ever one i hope did the best i could.also remember to oil motor bearings while you right their.do not oil inside part of bearing on back of motor where t...
...quot;non chlorinated" crap.
In fact, red-can Brakleen is exactly the same thing as CRC Electric
Motor cleaner, which is safe for electric motor insulation. Green-can brakleen would instantly ...
The blower noise could be hardly caused by the screw whitch secures the blower cage to the motor shaft. It is a laterally pointed-tip screw which should cut firmly into the motor shaft. If it does ...
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...