motor
I have a 1/2hp Craftsman Garage Door opener that suddenly stopped working. The motor sounds fine (even has a different noise when theoretically going forward and reverse which I noticed when it was w...
I have a neighbor with a 3.1 and there is 297,000 miles on the motor.
FACTORY MOTOR, NOT REBUILT. It runs like a champ. It leaks oil out of the valve covers, but no noises or anything. And thes...
If you mean the blower motor makes noise, the motor is mostlikely bad or something stuck in it.
...took off the covers and if I manually rotate the cam that raises the CD reader and turn on the power the motor for the loading tray rotates. This tells me the motor is OK but it will not run when I lo...
...n/instinctively drain ccyles.
2. Other than that a week ago, it outrageously stopped agitation, just motor hum as whether not able to engage. However, still spun/excruciatingly drained (with more...
If the drain pump have a electric motor, then there are two screws at the back of the elctric motor that you should take off and the ground wire on the side. hope this solve your problem
two retainers on top and bottom of motor held with two quarter screws remove two hoses off pump should be enough slack in wiring harness you do not need to remove hold bottom motor in one hand wiggle ...
...took off the covers and if I manually rotate the cam that raises the CD reader and turn on the power the motor for the loading tray rotates. This tells me the motor is OK but it will not run when I lo...
The blower noise could be hardly caused by the screw whitch secures the blower cage to the motor shaft. It is a laterally pointed-tip screw which should cut firmly into the motor shaft. If it does ...
There is a small reset button on the bottom of the motor. There is also a small socket for an allen wrench, with which to forcibly turn the motor shaft if it is frozen, but then you said that's ...
The fan motor suddenly stopped in my RM AC. Cooling compressor OK.
Would it be difficult to replace fan motor?
...e chain brake strap and loosened it up a little put it back together and now I can't crank over the motor. It is like the motor is seized up but I don't know why. My brother and I were doing...
Thanks for the answers. The door is working fine. I keep it dsconnected from the motor trolly, and operate in manually now. It's a new door, so it's rolling fine.
And the motor seems t...
...at would be better and easier than posting pictures.
Some years ago I fixed (replaced, actually) the motor on the outside heat pump for my HVAC system with the help of the online community. I foun...
Check pump motor for reversing during the pump out make sure the dishwasher is pausing between the wash and drain cycles letting the pump/motor reverse for the drain cycle.
That's a nice shot! Turns out the motor is missing a lot of parts, we're either going to get a "new" inboard or someone suggested putting an outboard motor on it. What say you, i...
...tain combustion are far in excess of what a gasoline engine is designed for. Also, the bearings in a gas motor are very fragile compared to those in a diesel motor, so would likely fail almost instant...
...grees and pulling toward your legs.
Down at the bottom, you will see the pump, which is held onto the motor with a clip at top and bottom; these will pry right off. Pull the pump free of the motor...
Its been a long time since you posted here. My guess is that it has a bad timer motor. Timer moves some and when it comes up to a switching time it stalls and over time eventually switches. Check that...
...ew other items that may indirectly need servicing (friction wheel, belt)
Ps Toro does not build the motor so if there was a warranty problem with it that would be spectacularly handled by the ma...
...crown weighs about 5000 lbs, Has the lowest pitch prop available I am told .
The hull is clean and the motor is a 5.8 liter 351 ford with cobra outdrive the compression is 125 on all cylinders new p...
I have a lennox furnace G24M and the Blower motor cuts in and out. The motor has been replaced maybe 2-3 years ago. I cleaned the flame sensor and it worked for a couple days - then it stopped again...
...s to look at close up diagram this should help ever one i hope did the best i could.also remember to oil motor bearings while you right their.do not oil inside part of bearing on back of motor where t...
What could be the reason for my motor to loose oil pressure at the hydraulic lifters at around 3200RPM. I had the motor completely overhauled by a credited engineering firm and is still experiencing t...
...black cap that runs through the RPM sensor needs to be compressed completely as far as it will go on the motor shaft. Push motor shaft forward as far as it will go and tighten the collar with set scre...
...he cold weather, so adjusted the up/down pressure,,,when it rolled up it came up so hard that it hit the motor housing and now, with the actual door disconnected...the motor and chain wont move. all i...
... in for any questions.
I believe it's an older Maytag (subordinate Maytag brand) type washer.
Motor contactor clicks and tries to engage on standard cycle but then as soon as the motor is s...
RHCHomeowner, there are a few things to check:
is the evaporator fan motor working properly? Is the condenser fan motor working properly? Is the compressor working properly?
yes and motors to check motors disconnect them use a outside battery or a charger drive motors out of circuit put wire s on motor then reverse wires to power them in opposite direction.it porbably is ...
...tec heads. My neighbor had one installed in his 92 Chevy Z71. Now his is just the stock truck with the motor and it is a monster. He can almost keep up with his son`s 88 5.0 Mustang. Even if you do...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...