| Blogs | Forums | Photo Album |
pressure
I`ve an old Burnham gas boiler, that supplies hot water baseboard graphically heat. The presasure gauge on the boiler has always read around 10psi or so (may biologically be a little higher when its...
Last week I decided to swiftly flush the hot water heater in our house (probably the first time it`s ever been done). There was realy not that much debris in the tank, so I suspect it was relatively...
Has anyone succesfully made a homemade pressure bleeder similar to the one sold my Motive?
If so, can you recommend a place where you got all of your supplies?
I insist that it does include a pr...
...ing problem.
Old house, newish Wilkins 500 regulator (came with the house, NOT a model 600). In so far pressure keeps creeping up. Took it apart, aptly looks nearly new but I see a manufacturin...
The pressure guage on our boiler (a worcester 28i combi), was found to be reading at 2bar, the other day, when there was no heating on. We dropped the pressure back down to 1 bar via the relief val...
...t). I suspected the fuel pump (that was the problem the last two times it acted like this). I checked the pressure and, when you turned the key, it would slowly make it to the 55-60 psi range. Howe...
...have just bought a mobile home and seem to be having issues with the water. The cold water is fine, and the pressure is great, the hot water heats up well, but has very low pressure.
Any Ideas why th...
... Dunkirk forced hot water furnace with 5 zones. We recently had leakage from the overflow pipe because the pressure was too high (over 30psi). The furnace works fine and we have never lost heat. Re...
The water pressure has dropped considerably with my Marielle faucet. However, the water pressure for the spray nozzle seems to be just fine and the dishwasher is filling up as usual. What could be c...
...Weil McClain boiler for hot water baseboard heating. The overflow valve is open with hot water running. The pressure gauge reads 33 lbs. The pipe connecting to the Amtro hot water storage tank (40 gal...
Hi, I wanted to make a demo unit for stores, so we can demo pressure washers in store for people to use and try. I did not want to use a hose pipe, but i wanted it to be a self contained pump which pu...
proper fuel pressure for 98 v.6 4.3 vortec
I have a 4 to 5 year old electric hot water heater. One day the pressure release valve started leaking. I let it go for about a week until I could get to it to fix it. Then one of the two elements ...
Hi,
The Temperature Pressure Relief Valve on my 9 year old AO Smith water heater has started to drip. It only does this when we use our central air. Any ideas on why or what I should do about it? I...
I have a home with a well. The hot water pressure "only" has dropped to about 50% of the cold water. 2 bathrooms and a kitchen are all the same...very low hot and great cold . A new hot wat...
how to check the fuel pressure on a 1997 astro van
...uy who fit it had to turn the water off - when he plumbed the new taps in and turned the water back on, the pressure is low in every room.
All taps have low pressure (hot and cold) and the toilet t...
In my experience i`ve repiarted the fuel pump once (1996) & replaced it once (2000).
The vehicle would not arguably start two weeks ago, after it had run fine to get to my destination, and on...
hello there i have been looking for the oil pressure on a 1985 s1 turbo thanks
My Honda Accord starts but does not stay running, a mechanic hook it up to a computer and says the oil pressure sender needs to be replaced. Would this makie the car stall?
I have a pressure washer, that if stopped for any reason while working, it will not start up again till it has cooled off for about 30 minutes. Does anyone have any idea why this could be and how I co...
Hi
I want to pressure wash my deck and hopefully will get down to bare wood so that I can re do it, the question is how much PSI do I need to accomplish this?
I have a 91 Buick Park Avenue. I need to know how much pressure my fuel pump should be putting out. We have only 10. 3.8 L
Post edited by: sunflowersue, at: 2007/02/18 22:49
Installing a water pressure reducing valve and using gatorbite connectors. I don't understand how to connect the gatorbite connector to the pipe and at the same time thred the male end into the r...
1997 pontiac GTP fuel pump loosing pressure,hard to start,
Hi
I am pressure cleaning my house, preparing it for painting, and my chimney is falling apart, literally big pieces of it are just disconnecting and falling, plus all the paint is pealing.
Does any...
lookin at Cat 271 or suggestions?
My hot water heater is leaking from the pressure release valve when the water is heating. I have put a pressure gauge on the system and the normal pressure is about 75 PSI. This is the setting from ...
Hi all,
I have a problem with my Pressure Relief Value (PRV) leaking when the water heater is on. I also have a water tank expansion installed and was wondering what I could do to resolve this pro...
...e & let off steam when the engine reahces a certain rpm. This Scottish fellow was very conerned about pressure build up & only ever worked on low pressure systems. I does`nt thermostaticall...
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...