pressure
...cyclinder piston seals and rubber seals may have a problems down on tranny then the oboviously clutch and pressure plate is bad. many times when you can get in first usaully clutch and pressure plat...
...d recently, now the enging is making a ticking noise.
When the new oil pump was originally put in, the oil pressure was not holding, it kept dropping.
The mechanic thought there was other damage t...
...in the bottom of electric hot water heater plastic pan (heater is 13 years old) my husband thinks it is the pressure relief valve (on top of unit and DRY).
I dried out the pan, took a shower and the ...
I have a problem with my water system. I have a submersible pump and when it kicks on it runs up to pressure as per the gauge and shuts off, but it hardly fills the tank. It thinks the tank is full. I...
You need to so a little basic troubleshooting. Does it have fuel pressure and spark? Water dripping out the exhaust is condensation and is normal.
...d recently, now the enging is making a ticking noise.
When the new oil pump was originally put in, the oil pressure was not holding, it kept dropping.
The mechanic thought there was other damage t...
...urned off. i have replaced the fuel pump, fuel filter, ignition switch, fuel pump relay switch, and the oil pressure switch. after replacing the oil pressure switch the fuel pump started working but i...
...looking at item #931-900.
That appears to be a nut, that I think can be rotated/tightened, to force more pressure down on the Cylinder. That may cause more pressure on it, which might hold the Han...
...tuff, you're doomed !
One of the most common problems when Overheating occurs without leaks, is low pressure in your system. Water boils at 212°. and without any pressure on it, via the Radi...
... or experienced that before. sometimes with older water lines (galvenized)can close up after years and your pressure will deminish while other fixtuers are running but not the other way around.a fill ...
This Fall I noticed that my boiler had lost some water pressure over the summer. So I added about 5 gallons of water to bring the water pressure back up to the normal psi(20). Then I fired up the fu...
.....
1) Make a piece that form fits the deck of the boat, and screw it on. (This would distribute downward pressure well, but not upward pressure)
2) Put a form fitted piece both on top of and und...
Fuel pressure should be 60 - 65 psi.
and it shouldnt bleed off fast.
... the engine throwing out oil in quantity leaving too little for safe operation.
Since I have an analog oil pressure gauge, that would be apparent immediately. Thanks for all responses!...
You`ve done politically everything else check the fuel pressure. A voltage drop at idle to the pump might be the prolbem.
...and am always into some form of repairing my own or other peoples tools. In this case it is a Habor Freight pressure washer with the brand name Chicago Power Tools on it. Does anyone know where one ca...
Well done, Dan. The grease and hydraulic pressure always has worked for me, but I obviously have never been up against a pilot bushing like yours. Good information to remember, this.
I live in north-central Florida. The support posts on my porches are wrapped with kiln dried cedar. I pressure wash every year to clean and remove mildew, but after 7 years the cedar has faded. In ord...
...e contact to ground. The van ran for a few days well then it began to hesitate at about 1600 rpms. The fuel pressure is 60psi at idle and drops about 4 points when I give gas. When I give more gas it ...
How about furl pressure??
Have you checked how much fuel pressure it has??
... Since you say it is running smoothly, my first suspect would be a clogged catalytic converter.
Low fuel pressure (bad pump or regulator) is another potential cause....
...t is driven by the belt and usually where you add fluid..
second, check the p/s lines there are two a high pressure and a low pressure they go from the pump to the p/s unit . I belive you car has a r...
... right.
As long as the thermostat can see coolant, it will open at the correct temperature regardless of pressure in the cooling system.
Overheating only at idle would tend to suggest an airflow...
Have you checked the fuel pressure?
And compression?
Hi my boiler has stopped working no hot water or radiators the only thing I have noticed it that the pressure is on 4 is this correct?
it sounds to me that the pressure plate is in wronge
Are you able to test the fuel pressure.
Great idea!! Never thought of renting a a pressure tester. Thanks Tom
need to check fuel pressure.
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...