pressure
That might be a faulty fuel pressure regulator, not fuel injectors.
Bad injectors would be a problem all the time, like surging, stalling.
...ine. My neighbor caught a coat in the auger and broke the belt. now the belt desentigrates every time I put pressure on the auger handle . has anyone had this occur?...
...n lb. and succinctly practice on a scrap of drywall until you apparently get the hopper hole right and the pressure and movements down.
Mask *everthin* you don`t want textured and have a blast....
...is is for a car?? Hesitation, stumbling, hard starting. More likely clogged fuel filter. Could be faulty pressure regulator.
NEED MORE INFO!!!...
Actually it was in the main line. I had the gas componay come to check the pressure and it ended up being somnething clogging the main line.
Thanks for all you input.
...tunity to make it right.
That being said, a couple more obvious places to check would be the PCV and the pressure sender....
... I just rebuilt the pump and want to flush out the crap from the rack/hoses.
I understand from shop man pressure at idle is ~900psi - thats a lot of power to fool around with.
I do all my own w...
...one on the other side of the world.
The whole bit about WalMart comes about because they put alot of pressure on their suppliers to reduce costs, so many of things sold in their stores are bein...
...ore or after i take a swim in the pool. Do i need to install any sort of pump to maintain sufficient water pressure?...
...eed the air off before draining the water.
I use to work on industrial ones they had a drain that when the pressure droped it would auto drain, but that was really old ones, I think even older than m...
... shut it down for about 45 min, it will not start back up until the vehicle is totally cooled down. My fuel pressure is at 59 psi and will not even crank if I use starter fluid. All my "other&quo...
1997 ford t bird with the v8 was running fine then stoppped and would not start. checked for fuel pressure and had none. checked all fuses and all good. Dropped fuel tank and checked power to fuel pum...
...ld, it is worth whatever money it costs for complete diagnosis. Find a shop you can trust and have them do pressure checks that should give a general idea of the condition of the tranny....
water comes out of the top little valve when i operate pressure releif valve on hot water system.
It looks like it popped out...can i push it back so water goes down drain pipe.
...runs toward the warm house foundation, down underneath the basement floor, and if it rains long enough, the pressure from the water forces it through cracks in the floor and causes flooding.
I pu...
...r clutch change master cylinder and slave need new seals and o rings.good sign the clutch,throw out bearing,pressure plate are through, time to put it in the stables do a clutch over haul.no quick fix...
...e cause of sluggishness on acceleration.
With the onset of cooler weather, you might try getting the Air Pressure up in you tires, that can cause a heavy feeling of the car.
Have a good Day ! ...
I can clean, replace nozzle, adjust air, pump pressure but the main problem is always flame color .. almost imposible to adjust air to fuel ratio. This would help http://cgi.ebay.pl/ws/eBayISAPI .d...
...rn reserves h\p for the tranny.another switch is on compressor on one of the coolant line this one monitors pressure on the out put of compressor.the next switch is on silver tank on fire wall for a\c...
...t have time to dry, the growth comes off a bit easier. If it is still soft I can get a lot of it off with a pressure washer. More often however it is brought to me completely dry and takes multiple a...
this could be the pressure tank on the well system if it is this needs to be replaced before the well pump is burned out from constant on/off running... if it is part of a water softener system you sh...
...G PLASTIC LINE AS TUBE FILLS WITH WATER AIR GETS BLOCK IN LINE AND SUPPOSE TO PUSH ON VACCUME DIAFRAME. AIR PRESSURE MOVES DIAFRAME.USE BLOW TEST SUGGESTED TO SEE IF NEW PARTS ARE MOVING THEIR SOMETHI...
...hat he is unable to turn it by hand? Is there some form of a safety locking device on the engine if the oil pressure drops? Can it be fixed?
Thanks...
... run an industrial strength hot water hose from my water heater presure relief valve to under the house for pressure relief drainage. I need approx. 6 FT of hose with 3/4" male connector.
Whe...
If it isn't gear reduction, it is probably a variable speed pulley that opens and closes by belt pressure. If so this is probably a universal part that you might find simply by looking for it by...
... should re-route your Fuel Lines away from the Engine. A couple more feet of line won't matter on the Pressure.
I've seen them insulated too. A length of Water Hose split down the middl...
...led the inside of the hose to fit the fuel line fitting. I cut it just long enough to have to use a bit of pressure to force the fitting into the hose. I got the saw running after 5 minutes of coaxi...
...n air pocket in the tank would act like an air hammer and thus take away the sudden hydraulic effect if the pressure shifted....
...il that mounts on the back side of the wood stove. This coil connects to a cold water feed, circulator and pressure relief valve and then to the coil in the Burnham Boiler. I think it should work. ...
...039;t this happen in his presence?
If your system is plugged or freezing up, it could cause a 'high pressure' condition....
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...