pressure
...a few times, and then crank the engine, if it starts, then the problem is that the fuel pump is not holding pressure....
... a light it and then go it will cut out and stall. Once I get started moving again it runs fine. It there a pressure cutoff switch? Any help? It's starting to get warm outside and I can't dr...
...logged. Flame at the igniter looks good and the flames at the bottom all look good. The plastic hose to the pressure switch is not clogged.
What can I test out next, procedure for testing, or what ...
...il that mounts on the back side of the wood stove. This coil connects to a cold water feed, circulator and pressure relief valve and then to the coil in the Burnham Boiler. I think it should work. ...
...039;t this happen in his presence?
If your system is plugged or freezing up, it could cause a 'high pressure' condition....
... a campbell hausfeld framing nailer. it works fine but seams to miss fire every other nail. it might be the pressure is too low(90PSI) i got it rebuilt off of ebay for $45 i think. don't forget y...
My hot water coming from my kitchen sink has stoppped working. I still have water pressure on both hot and cold side and hot water in all other areas of the house, just not from the kitchen sink. Wh...
...th a tecumseh 5hp tecumseh engine.the motor is un repairable .I have a briggs and straton 7hp from a broken pressure washer.Most of the briggs would match up except there is no pto shaft like the tecu...
...e way with the lug wrench and then torque them to spec. A this point they`re stationary and there is some pressure on the torque wrench to get the pointer to move.
For disc brake calibers and v...
...-rings into shreds in the process because of the zero lubrication properties of gasoline. A subsequent fuel pressure test made my fuel system look like my lawn sprinkler system.
After replacing the...
...erature set to middle for hot water but can only get tepid water from all the taps in the house since water pressure was adjusted at main inlet. Prior to this water was scalding hot from all the taps ...
What could be the reason for my motor to loose oil pressure at the hydraulic lifters at around 3200RPM. I had the motor completely overhauled by a credited engineering firm and is still experiencing t...
...ht should reset as soon as the engine started their no reset that i know of per say.
either their no oil pressure or sending unit is not signaling. i know oil light getting voltage because its on....
You should probably replace the oil pressure sending unit also. Generally it's a simple matter of unscrewing the old one from the block and putting a new one in...
... Oil light coming on is ...
... lots of rust. Runs great, but moves too fast in forward (1st gear/speed) for proper snow removal. It has a pressure wheel against a larger wheel for a drivetrain. Can this be adjusted to slow forward...
...d or overflow.
USE CAUTION for the next step i am describing!
To check while the car is cool and no pressure in the rad, take the rad cap off and then run the engine and see if there are lots ...
...er lines and pumps out the old fluid while pumping in new fluid. It can sense whether you hooked up to the pressure cooler line, or the return cooler line and it adjusts as needed.
So there is no fe...
... of the shower and/or you have a venting problem and/or the shower drain is so close to the washer that the pressure of the water being pumped out of the washer is easier to come up the 'low'...
...your drive belt and idler pully and if the belt slips it means your idler pully isn't applying enough pressure on the belt, so your reverse will be slipping....
if this is a gas engine theirs no pump as such its the fuel pump in gas tank electric pressure should should max to at least 22 psi depending on throttle position sensor gas peddle
if diesel do n...
...39;m getting no feul to the engine, i have power coming out of the fuel pump relay but no juice to the high pressure fuel pump, i've changed the fuel pump relay and also push a button down that I...
...ew head bolts and go through the proper torquing order according to the manufacturer.
The head should be pressure tested if there was an engine failure....
...wer plate, then push on the rod (by holding it against the bench) while pumping the lever. With that added pressure on the grease cartridge the pump should begin to pump grease and the trapped air sh...
...eplaced the fuel pump 2 months ago and on the 2nd fuel filter in 2 months. when it dies you can release the pressure on the rail and all air comes out. barely any fuel. it wont run for an hour also. t...
... tighten the collar with set screws. Put black cap back on RPM sensor. After that try adjusting up and down pressure. That that might solve your problem.
-Jeff...
...ave a freon leak somewhere in the system. If you have no freon, then the compressor will not come on. The pressure switch in the ac system tells the compressor if its safe to operate or not. I woul...
...delta 88 both had this problem cheap and dirty fix trans-x 2 cans do not drain off surplus you need all the pressure to flush out valve controls and govenor add one thrid can every two days hot trany ...
Without applying too much torque, you can use whatever type of pliers and apply slow, steady, even pressure, to the stem or handle, in the open (counter clockwise) direction. Once it breaks free, it w...
...ntana. It has the 3.4L V6. For some reason it has been blowing all of the oil out of the oil filter at high pressure. It is blowing the oil filter gasket out the side and then shooting all of the oil ...
“How-To” Adjusting Packing Nut.
Greetings duckarama and welcome to the Forum !
First of all, we need to establish some terminology here, and the thingy that you’re dealing with, is called a Dive...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...