unit
... or Phillips 47MF437B
No Picture / Green LED / Good Sound / All inputs
When power is applied the unit turns, on, whether from remote control or power button on unit. The backlights turn on and ...
Astronut, I'm afraid you would need a detailed diagram of the unit for that mentioning the exact size of the wall. Maybe you can get to a car-depot (garage) and ask if they have a 305 TPI at hand...
... However it will not separate. Does anyone have expertise. I don't want to pry or pound on this unit. Help!!...
...ne I wanted to use to swap into my project RX-7
UNTIL I did a little checking on it. Apparently, this unit was full of problems.
If anyone can comment on the 3.4 DOHC, I would find it very intere...
...everyone!
I did the adjustment on the "effort" knobs by the white wires in the back of the unit last evening and it worked!! Hooray!
Thanks for everyone's advice!...
recommended you should always turn off the power.will damage heating unit if it doesnt burn down the house first place.
it is a indoor free standing unit
and the blower fan is very noisy
...onal white line in the middle of the screen. The past few weeks I have been able to hit the side of the unit and the picture would come back. Now I can not pull the old fonsarelly move (spelling)
Fr...
...ctrode gap was a little tight and he lengthed that out. He also suggested that I change out the burner unit, regardless of whether what he did worked. He said the one I have is inefficient. This fl...
...ft was worn even though it did not appear to be.
Starting leaking again, and I ended up buying a new unit.
Was good experience, but time wasted in my case. You might be luckier...
R56W36 while tv was on a screeching noise came out and the unit turned off. it turns back on and shuts down within seconds. 5 years old.
No, I still haven't figured it out.
I can easily open up the back of the unit. I took the opportunity to clean the lamps themselves - which were dusty.. but that didn't address the issue.
As you have found out they the Cat unit must get really hot. if not they clog and cause lots of problems. rotten egg smell. That Beemer is a costly little auto but
I guess you know this fact already.
1997 ford escort 2.0 cooling fan won't stop running! I changed the sending unit is there a fan relay and where?
My in dash unit will not read cd's when they are put in, i was wondering what the problem is. It keeps saying bad disc
...ere adjusted properly. The only way the door will completely close is by pressing and holding the wall unit but as soon as you release it the door reverses opens fully and the light comes on and flas...
...e problem. I am truly hoping someone wiser than me, will respond to your posting with a solution.
My units is a 1/2 HP Craftsman Unit from 1997....
had to replace my dodge truck sending unit twice because it stopped reading
say what you want ...they should be better built
That's what my unit does too. Flash the green LED after it remembers a remote's code. I'm out of ideas for you then. If it's not remembering the codes there's not much that ca...
How does the pivot / tension unit work to remove the belt? I am use to the adjustable alternator brackets.
...e ceiling! How can that be? He did't know what to do... we did try replacing the battery, and the unit.
Thanks!...
You should find that is quite a simple unit. Single water tube that should stay in the back of the freezer and the plug in electrical connector that really can't be put in wrong.
...uld say it is likely that the pump's start capacitor has blown. the dielectric (if leaking in the unit) can cause intermittent shorts.
Good luck!...
...ce would not start.
I opened the access door to the furnace, then loosened the feed line to the burner unit and discovered that there wasn't any oil in the feed line. The bobber in the sight g...
i have a york gas furnace and the pilot light go out after the furnace cycles a few times the unit is approx 17 yrs old what is the problem
...r on his circuit boards.
I don't think they will know anything at yamaha without looking at the unit but ofcourse it's a good idea to ask anyway at yamaha support
So yes Jeffie, you ar...
Assume updraft furnace. (blower on the bottom) Remove power to the unit. (usually these plug into the wall close to the unit; might be a switch; or find the circuit breaker (should be separate and ma...
.... I`m trying to absurdly find a set of plans/blueprints for eventually building a steam distillation unit for water. For the first time any info on where I might consistently find plans would acc...
...ore precise about the amount of chemical you administer, and only drops the chemical directly below the unit, making the application of Herbicides quite safe, when applications are made directly next ...
...EC1001 soldering station seems to flicker then turns off. Is there a thermal overload sensor inside the unit? Can it be replaced?...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...