unit
...DT-1704C 17" monitor. It powers up with no
HV. I was carefully prodding around the power supply unit and inside is a
TF341M thyristor (I looked up the datsheet). Using the diode test on my D...
...in order for the door to work properly. The only way to get the light back on is by luck or to tap the unit until the light goes on. Any help/input is appreciated. Thanks....
...(5.7). I chased this problem for months. Apparently TBI's are noted for the gasket under the TBI unit to deteriorate (mine literally burn away). When I was finally advised of this, I had it fi...
located on the bottom of the unit spanning from the bottom of the door to around 3/4 the way back. dishwasher must be pulled out from cabinet area removing the two screws securing it to the counter to...
i have problem with jvc GR-D53AG. after 3 mth in store and when i turn it on there a message E06 UNIT IN SAFEGUARD MODE,REMOVE AND REATTACH BATTERY.i follow instruction and nothing happen.Cannot recor...
...to get parts. Your best bet might be to send it off for repair, unless you can get your hands on a DOA unit for parts for cheap.
Good luck!...
I am having the same problem. On/Off switch making noise (easy to locate from above the unit as per its sound) and now has failed completely. Thought it might be dust between connections, but after so...
Not working as of yet. My brother has installed this same unit so he will be here tomorrow to help me out. I purchased a new t-stat today that takes 3 wires. I guess I do need to send 24v to the t-sta...
Central HVAC, 3 ton unit, at 90 deg. ambient, 70% RH, what would the normal temp be expected at the return line to the compressor if the home interior is 74 deg. ?
...ard fin tube radiation, it could be air-locked and would need to be bled. If that is the only baseboard unit in the loop, the zone valve may not be opening. Not enough info to accuratly diagnose your ...
...o the Forum.
I'm not sure that there is a R/R for something like that, it probably was with the Unit when it was new.
Apparently you don't need it, but, maybe you should leave it on th...
... slower. After that it works fine all day. The problem is only on Start up. Can this be fixed or is the unit going....
...t it will hastily fit the existing rapidly mounting brackets, then I would just optionally replace the unit. Most of the tricky work is in the mounting and locating. The repair parts are very expens...
...problem
I've replaced the sproket assembly in my 1/2 hp Craftsman chain drive opener and now the unit will only runfor about two seconds one directionand then two seconds the other direction. A...
...o the red (temperature gauge). And my eletro fans don't work but they work I by-passed the sending unit and jumped them to the battery and they both work fine.....
using the correct bulb? i have a lightbox projection unit that does this when the bulb is going bad or if i put the wrong bulb in it. i.e. try a higher wattage same cofiguration bulb if not the protec...
I am building a hydrogen unit for my truck. I know that i must use stainless in some areas due to the reaction of steel with hydrogen, but is stainless a good enough condustor to use as an electrode i...
...r controlled by the board. The motor is drawing too many amps causing the resistor to burn up. If the unit is only one year old, I`d call GE and try to get it repaied under warranty. The fan motor ...
...he remote or if you use the on/off switch. Can't seem to revolve the problem even if I unplug the unit. Can someone out there tell what this problem is. If was working fine up to that time whe...
...lanning to replace the standard radio/single CD Player in my '03
Saturn Vue with a Panasonic head unit and a Sirius satellite radio receiver. Does anyone have any advice on the radio removal / i...
...39;t think any have claimed to be psychic!
Maybe a model # plus a general type description of the unit, plus a description of the specific problem, and what troubleshooting you've tried to ...
...ND I THINK MY FAN LIMIT SWITCH IS NOT WORKING, THE HEAT EXCHANGERS WANT LITE UNTILL I TAP THE FAN LIMIT UNIT, COULD THAT BE THE FAN LIMIT OR ANOTHER PROBLEM?...
...rmly force is to not use the bottom 10% of a torque wrenches` range, even whether it`s calibrated. The unit may not be 100% accurate at that point. So, if you have a torque wrench that`s rated 10-10...
...
i wwas told by the dyson help desk that using a rubberised plug does not void the warranty on the main unit.
the callout charge in case damage to the dyson plug is because of negligence is 25 poun...
...have had this issue since the initial installation six years ago and two technicians have looked at the unit and found nothing wrong. I service the unit myself every year and do not have a problem wi...
...ia radio (probably AM) a sound from a mp3 or cd player. I also would like to build the speaker/reciever unit. This needs to be somewhat loud, and I was wondering if anyone could help me out here. I kn...
...r old house has a Trion electronic air filter on the furnace (heat pump). My hunch is that these older units are not very effective and don't the air very well.
Anyone with experience? Wou...
...n when you start it by hand, I'd guess that the belt is slipping. You said yours is a direct drive unit but there must still be a clutch or transmission of some sort to go between the agitate and...
Hi. Does anyone know what could be going on? I live in a upstairs unit of a condo complex. Yesterday I noticed that when I tried to turn on the hot water in our hallway sink and washer, nothing com...
... it acouple of months ago with any problems. I want to convert some tapes to DVD but at the moment the unit only powers up for a few seconds, indicates a low battery and then shuts down. The battery ...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...