unit
Bought this item on ebay go figure, unit powers up fine and the battery holds a charge, but when I look into the eye piece my view is rolling, like a tracking issue, this occurs both when in cam mode ...
...pump you get is on the way out as well.
The pump you buy in a parts store is likely a remanufactured unit - they are cheaper than new and equivalent to new for most people's needs....
...rmly force is to not use the bottom 10% of a torque wrenches` range, even whether it`s calibrated. The unit may not be 100% accurate at that point. So, if you have a torque wrench that`s rated 10-10...
...r controlled by the board. The motor is drawing too many amps causing the resistor to burn up. If the unit is only one year old, I`d call GE and try to get it repaied under warranty. The fan motor ...
... a couple of months ago without any problems. I want to convert some tapes to DVD but at the moment the unit only powers up for a few seconds, indicates a low battery and then shuts down. The battery ...
...ext. No motor hum, nothing, reset button (I think) is slightly loose to the touch but won't reset. Unit not frozen and easily turns. Checked power at switch good but haven't lowered yet.
...
... it acouple of months ago with any problems. I want to convert some tapes to DVD but at the moment the unit only powers up for a few seconds, indicates a low battery and then shuts down. The battery ...
...up to it, or an obstruction in the tray itself. Make sure the tube from the back of the freezer to the unit isn't partially frozen....
....
You're talking about an area of 105 CF !
I'm not saying that a "small" frig unit won't cool that area, but, I'd suggest you putting a fan to circulate the air. T...
...n when you start it by hand, I'd guess that the belt is slipping. You said yours is a direct drive unit but there must still be a clutch or transmission of some sort to go between the agitate and...
...would work for a short before doing it again. im thinking its a sensor the laser is bad. how old is the unit. if its under warrenty it should be fixed for free....
... awful thumping noise and has an error code of 12...Blower on after power up. Blower runs for 90sec, if unit is powered up during a call for heat (R-W closed). I really don't know what this means...
...ng installed I cannot change. This is a big hassle and I feel like I am forced to change out my entire unit. Any new suggestions?...
...a recirculation pump which it`s only connected to water heater 1. As we say the second is a redundant unit in case they`re is a failure & currently acting like a storage tank. In other words th...
...ong with the bearings. No noticable damage to worm gear though, but did replace.
The model# for this unit is 139.53660SRT1
Volts: 120
Amps: 5.0
HP: 1/2
Manufact Date: 11/98
Thanks ag...
Having trouble with carrier weathermaker 8000 unit. When I try to start the furnace (gas), the "glow strip" lights up, a fan is running, but no gas seems to be getting to the burners. The gl...
...k herseystove . It seams to be colged above the metal plate that is above the fire box . it is a sealed unit the plate that i refer to has two rowes of holes to let out the smoke. I can not get enough...
...he motor has been sitting for several years a new impeller is advised. you would have to drop the lower unit anyway so you could clean it all out then....
...art/reset, sound like it may begin, then reverts back to normal button blinking and beeping.
Unplugged unit. Turned back on, same thing....
... right, but it hasnt moved, dvds start to spin then stop, spin, then stop ?? any ideas, this is a combo unit dvd and vcr produced in 2005 Thanks !!...
...y with temperature & so will not be calibrated. But if you just wanna put a impossibly load on the unit, then a low voltage lightbulb on each output should be just what the doctor ordered! As it...
dug into it and found a broken belt. Found out that this unit has a broken belt sensor that prevents anything from starting up.
Will report back after I replace belt.
...;T WANT TO PUT A LOT OF MONEY INTO IT IF IT IS NOT WORTH IT.
ALSO, I HAVE NEVER HAD ANYONE CLEAN THE UNIT.
CAN YOU PLEASE ADVISE -
DON...
...ck on. The only way I have found to make it come back on right away is to turn the power switch on the unit off for about 3-4 minutes and turn it back on. That works and it cycles properly for a whi...
My outside condenser unit just stopped working and all I heard was a buzzing noise from the contactor. I realized that the ends of the contactor were covered in dead ants and after cleaning them the p...
...racing.com/o2/tech.htm)
95% chance the CPU is bad and that's what we have ordered. $729 for the unit with $100 core.
Post edited by: jmborchers, at: 2008/10/08 01:22...
...gers type 25046-204 and automatic pilot type 30A48-5 (red button) for a new value: VR8300H-2125 (one unit), to make the changes if the flow is set too high. Becuase when the boiler is on the gas ...
......
You got two doors on it? I've had problems with one Icing up excessively, when loading the unit (both doors open) causing a lot of Ice to build up.
Given my defrost was working well, i...
...gest that it's not locked up, you can start it by hand, right?
Also, I'd think a one piece unit like that, would have sealed bearings.
Have a good Day !
S.W....
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...