unit
...ccur. The single most common point of failure is the start capacitor for the pump motor in the outside unit... Especially in the middle of the summer...
It's a $20 fix if you work safely, i...
......
You got two doors on it? I've had problems with one Icing up excessively, when loading the unit (both doors open) causing a lot of Ice to build up.
Given my defrost was working well, i...
...gest that it's not locked up, you can start it by hand, right?
Also, I'd think a one piece unit like that, would have sealed bearings.
Have a good Day !
S.W....
...nd convergance come from same circuit you either have another cap or resistor out of value.also on this unit check solder on convergance board look for solder bridges were you replaced parts i have do...
Sure.
Just don't expect to find much info on it. Generally, replacing the whole unit is far more cost effective than trying to repair it, Since you can generally get one for $100 or so (depen...
You should probably replace the oil pressure sending unit also. Generally it's a simple matter of unscrewing the old one from the block and putting a new one in...
... Oil light coming on is ...
Oh, I didn't realize your unit had an external transformer (all my LCD monitors only have internal transformers), but all external transformers (that Ive ever seen) have a thermistor also, my und...
Thanks S.W. for the quick response.
Yes it is a residential unit.
Not sure if I have a Check valve on our main supply but I suspect we do. It's a 5 year old townhome.
I need to check the ...
I have just had installed a 12000btu carrier Split Unit. The distance between the indoor and outdoor units is about 22 meters (70 yard). The cooling is fine but when turned on a hissing sound is very ...
...ve spent a bit of time working at a Saturn only shop.
My advice: Replace the tensioner with a quality unit.
Yes, they go bad, and yes, it will make exactly the noise you describe.
A quick test: P...
...n good shape (no looseness) and the vibration occurs when the fan speeds up.
As far as accessing the Unit, look for any removable panels which would give you access to the area.
I have used Sili...
...eating Elements may not be on the same circuit as is the blower.
2.
Heating Element may be bad in the Unit, takes an Ohm Meter to check those.
3.
Could be the Contactor as Jeffie said, or, the con...
...edite draining the Tank.
3. By the time the Tank is drained, there should be sufficient time for the unit to cool, where a backflush can be done safely.
4. I think you're already tried just...
...grammable digital one in it's place. As lexmarks said though, make sure it'll work with your unit.
Most will work together, but if you have a heat pump, make sure the controller will w...
...eplacement on an Ariens ST824. I'm all through with it. Got the belts on the correct way and the unit is put back together. The problem is my auger drive belt keeps slipping off the auger pull...
...re finding -- it is very rare that the door goes down on the first click (either from clicking the wall unit, outside keypad, or FOB/home link units). What it does is the gear holding the chain (spro...
...for test if the overload pop thats all u need to know to replace it.
make sure you shut the power to unit before you work on it = P...
...ings on charge and for get them for days. in hot climate batterys destory them selves.the only fix this unit total replacement of the battery....
...ike welcome to the Forum.
I'll tell ya right up front, I'm not familiar with either of the units you're using there, but I got a fair concept of control wiring, so.....
It may be ...
...9; 12/3 gauge. Does "not recommended mean I souldn't use a 12/3 at all?? This is a 4HP 400cc unit, I don't know the amps . Also if I could use 100', could I use (2) 50's woul...
...tes either model 363.15171, or 363.15179.
I can not find the model number in the usual places on the unit, and had no luck searching the Internet with the 363. numbers on the guide.
I need a pus...
...ted...the motor and chain wont move. all it does when i hit the button is hum. ive tried unplugging the unit and also adjusted the up/down pressure...what is my next step? taking off the chain?...
... in case I can help someone else out and to close out this thread.
I put the fan motor back into the unit, put everything back together using the same parts (no new parts), and...it worked! So the...
..., and the grounds are solid (no resistance) then you will need to drop the tank and replace the sending unit....
...to hold down the flusher. The flapper does not "stay up" to let the water out. I changed the unit inside and threw out the old flapper only to find that this annoying thing is happening tha...
... iTunes. This helter-skelter behavior lasted for an hour or more.
I also noticed a click (inside the unit) before each cutout (resembling the sound it always makes when I turn it on). Since then, i...
...y and the cable runs into the cab right behind the drivers seat,quessing there was at one time a VASCAR unit mounted there and the speedo cable went to that,the big problem is not the cable,however sa...
... over but not start unless the Oil Pressure is up to proper level
I replaced the Oil Pressure Sensing unit but that has not solved the starting issue. The Dash Guage shows proper readings once the e...
...simple terms) If it only gets back the data it sends, it'll know it's not talking to another unit. it will (probably) figure out there is a short in the cable (correctly as it were), and co...
...ith rca connectors switch tv to video in see if you have signal composit video and audio.if not replace unit not worth fixing cheaper to replace....
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums |
TIP: Write your question in details [ why? ]
Sponsored LinksLatest Posts
|
more posts...