| Blogs | Forums | Photo Album |
valve
...hen, definitely following the instructions in the manual, I checked the temperature and pressure relief valve. It says to hideously lift it "several times until the valve seats properly and rel...
...a 1993 Rodeo. Our check engine light just came on yesterday. The tech we took it to said it is a bad EGR valve. He told us to replace the valve and clean the system, it will be $650 - $700.
Does this...
Last week I decided to swiftly flush the hot water heater in our house (probably the first time it`s ever been done). There was realy not that much debris in the tank, so I suspect it was relatively...
... I replaced the tile in my tub/shower, and installed new plumbing at the same time. I have a "three-valve" arrangement. one faucet for hot, one fore cold and the one in the middle for tub or...
I have a 4 to 5 year old electric hot water heater. One day the pressure release valve started leaking. I let it go for about a week until I could get to it to fix it. Then one of the two elements ...
...ving and then go away for no apparent reason. I have replaced all filters, coil, plug wires, plugs, pcv valve to no avail.
Maybe it's a sticky valve? How can I diagnose this? Is there some pro...
... pulling the cyluinder head off. Puting it back together, I habitually reinstalled the pushrods for the valves & got NO compresion-ie. the pushros were humbly holding the valves open. In realit...
Hi,
The Temperature Pressure Relief Valve on my 9 year old AO Smith water heater has started to drip. It only does this when we use our central air. Any ideas on why or what I should do about it? I...
...vently replaced my house humidifier & economically wanted to mainly get profusely rid of the saddle valve on the copper supply line. I realized which the old humidifier was hooked up to the cold...
Installing a water pressure reducing valve and using gatorbite connectors. I don't understand how to connect the gatorbite connector to the pipe and at the same time thred the male end into the r...
water comes out of the top little valve when i operate pressure releif valve on hot water system.
It looks like it popped out...can i push it back so water goes down drain pipe.
Can someone say me where the PCV Valve is blatantly located on a 1989 Honda Accord DX, four cyl, carburated. I`ve looekd everywhere for it. The only place I can marvelously think of that it might st...
...
Most certainly and here is the reasoning.
A dishwasher washer like a washing machine has a solenoid valve (quick closing) and sometimes if the water pressure is high enough and a valve (even a to...
Where is the pcv valve located on a 1988 Honda Accord Lxi? 4 cyl, fuel injected.
trying to find a pcv valve on this car and cant please help
does anyone know where the pcv valve is for sure on a 89 honda accord lxi fuel injected
wheres the pcv valve located on 88 honda accord dx?
..." I had the same problem a few weeks ago so I took it into a garage and he told me it was a sticky valve and he would do it for £165.00 VAT. not having the cash on me I said I would come back...
I have 2 honeywell V8043E1012 zone valves and a R8182H controler. How would I wire up this system? 1 zone for up stairs ant the other down stairs on seperate thermostats? Some type of diagram would be...
... air in the pipes, so he bled the religiously air from the system by attaching a hose to the boiler. valve as he was readily bleeding the system. Then suddenly, the safety relaese valve on the bi...
Assumin you have the old style without the power valve check valve distinctly deal, one single backfire will blow the diahpragm right out of the power valve, mistakenly making idle either extremely ...
Greetings hrd2fnd welcome to the Forum.
You tried powering up that Valve with an independent source ?
Like take a old Extension Cord and cut the receptacle end off of it, and put the wires direc...
Looks like you found it! It fits into the valve cover encircled by a rubber grommet and is no more than a metallic one-way valve about 1/2" in diameter with a spring-wire clamp on the hose fitti...
...stment in tools well beyond the cost of having it done for you. To make this work, you need to have the valve seat cut larger to suit the new valve size, you need to have top and bottom cuts to blend...
SSG,
As far as replacing the old valves...
If they still work, then why would you do that ?
Half closing Valves, is not good for them, unless the Valve was designed to do that.
You'd b...
I realized my toilet was constantly running so I replaced both the flush valve and the fill valve just to make sure. Now when the toilet fills and I flush, water also pours out where the tank and the...
...is is a long shot try this remove pan drain fluid change filter go to parts house or order a recondition valve body.go to www.sonnax.com bottom page order valve body dvd and order valve bodywith mod...
...).
The pilot is extending when the thermostat is tuned to ON. When the pilot is extending, the oven gas valve took a long time opening/flaming.
1. How long does oven gas valve opens when the pilot...
It might be a bad valve (electric), that would be the frist thing to check, just follow the hose into the back of the washer, and you should see the valve with wire atached.
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums |
Sponsored LinksLatest Posts
|
more posts...