voltage

Forum Post Kenwood PW18-2 Power Supply Repair
... a print the electrolitic capacitors have a volt age like 4700 uf 50vdc or their abouts.simply divide that voltage by two what the sum is is the voltage i assume you know what a rectifier bridge looks...
Forum Post I have a mitsubishi wd-52627. Lamp went out in it. Shattered...
...vice shop claims that the lamp he sold me will work on my model even though it is not listed for my model. Voltage and wattage for lamp is correct, except arc gap is 1.0 instead of original 1.3. Also ...
Forum Post How to remove Toyota fusible link
...both the brake and battery light come on when the alternator's output is less than the battery's voltage. When I crushed the pins for the fusible link and soldered a wire in its place, it he...
Forum Post Can you build your own solar panels?
..., all a solar panel is is a bunch solar cells wired in parallel and series (depending on desired output in voltage and amperage, and the source solar cells) Different size/ type cells provide diffe...
Forum Post Heater/AC blower motor problem
...o some testing, go for it, since you have the votlmeter anyway. At that time when you dearly maesured voltage like you did, there was no load. So the reading will be 12 volts, regardless of evid...
Forum Post Hot and ground reversed: Home electrical problem
...t an electrical outlet tester & discovered Hot/Ground reversed. I took a multimeter & their was voltage amongst hot & steadily ground and no voltage bewteen neutral and hot, and no vol...
Forum Post GM Alternator Problem
What`s your battery voltage? Shouyld be over 12 with the key off. I suppose voltage famously drop could relentlessly bring it down to 11 at the alt... but Im fortunately thinking may be a bad cell i...
Forum Post tv trouble shooting part two(visiual inspec)
...say dead set with out a print analog chassic. the first thing i do is follow the power cord and locate low voltage power supply check fuses .also some tech do not realise that low ohm resistors 10 ohm...
Forum Post Mitsubishi 55inch Big Screen with lines
theirs two large heat sinks on horizontal vert voltage board i think on right side.they look like str packs.about size of a zippo lighter.one is for vertical output the other is convergence out.this f...
Forum Post no spark
Red wires on fuel injectors is hot from key switch use a test light turn on/off key to see if voltage is present or not if is present then fuses are not blown to that system. sounds like hall effect p...
Forum Post tv trouble shooting part three(neon tester)
high voltage power supply is another power source with secondary voltages that runs tv just after start up.so lets say your on a service call with out a print tv has sound no picture.this is several r...
Forum Post Starting current of 13.5KW pump
what is the voltage of the motor? How many phases?
Forum Post Kenmore gas dryer not heating
Well, my first question must be are you getting voltage to the element?
Forum Post what does flyback tranformer do?
...ion with horizontal output transistor/deflection circuits boosts the b+ (120 volt typical for a tv) of low voltage power supplies to 20 to 30 kv(kilovolt) for the crt analog tv.as well as provide vari...
Forum Post JVC AV-K25MX2
how do i adjust the flyback transformer voltage. where would i find it?
Forum Post need help with building car charger
Hi Skatewabbit. welcome here Wouldn't a regular voltage converter do?
Forum Post Toshiba Vertical IC issue
...rking for an electrical company for the past 12 years, but not in circuit boards. I have experience in low voltage and high voltage controls so I think I may have a shoot at fixing the unit with some ...
Forum Post help
what is the voltage for a crank senso for a 1988 delta 88
Forum Post 97 S10 Issues
Have you checked out the suggestions the manual gives you? I think that might very well be a voltage problem - now you mentioned it.
Forum Post Tektronix 7633 and 465
Luckily look for a PS rail with a large ripple voltage on it.
Forum Post Kitchen-Aid Dishwasher
...could either purposefully measure the resistance across the two terminals or you could supply the proper voltage (usually 115VAC) to the solonoid to exactly see if it activates. Even so the solonoi...
Forum Post CD will not spin up
As you may expect probablly. Check voltage accross the motor when it is immediately trying to focus
Forum Post my alternator is only putting out 11.5 volts, so...
What are yoy using to check the voltage?? The stock gauge can be wrong. And the voltade should be checked at around 2000 RPM.
Forum Post rough idle and stalling defies solution - `95 Jeep GC 4.0L
You`ve done politically everything else check the fuel pressure. A voltage drop at idle to the pump might be the prolbem.
Forum Post Hot/GRD. Reverse and ???
...ed all breakers off then on. Power still not on. Went to local box store and got multi meter, non contact voltage detector, and circuit tester. My plan was to check from breaker in. (A plan I shoud ...
Forum Post tv trouble shooting(no print)
...area.to convert pulseing dc then convert to smooth dc simple find the electrolitics capacitors look at the voltage rateing on the caps near the diodes know simply divide voltage rateing by two then th...
Forum Post tv repairs - samsung large format MODEL SP-56K3HX
Hi Adrian, welcome to the forum I am glad you joined us. It is either that or it can be a high voltage discharge, I think. Hope the new power supply will solve the problem
Forum Post trouble with 02 sensor bank1 sensor one
...g it. I think it is on top of the engine. A3.4 litre buick rendevous. Second I am getting a code for low voltage in position two sensor. Can anyone help? Thanks...
Forum Post Car wont start after accident
In case anyone is wondering, it turned out to be some kind of sensor related to the clutch (voltage regulator?). Never heard of this before but it was a quick, easy fix.
Forum Post magnavox rear projection tv
...blem there, but there can be SO many things that could cause that. Be careful when inspecting the unit, voltage is stored in several places in it, and could cause a serious shock. Take care! Ha...
  << Back 1 [ 2 ] 3 4 5 6 Next >>

The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 DIY Forums