wire 
The difference is that the older starter has three, so when you are cranking the engine, the third wire gives power to the distributor, the (s) is for the wire from the ignition switch.
The reason ...
I have a multi wire circuit breaker that won't reset. Nothing is plugged into the outlets for this breaker. It is probably my own fault, but I would like to get opinions.
There was an ava...
How do find the hot wire in a older light switch when there are only two wires the same color and no ground wire.
BEN
How do I wire up 4 fluorescent lights with a 2 head light switch and with a witch wire, using a 12/2?
with matching wire - your right white to white - etc.
Metal bax is not necessary, there is always a ground juntion.
And the joints wire to wire need wire marrets.
And as for wire - if its in th...
what do I hook the ground wire to coming from my new outdoor light fixture. Only 2 wires from the house to outside a white and black wire where does the ground get attached
Can I wire the exhaust fan/light on one switch.
There is two switches in the bathroom. One switch controls the lights over the sink and I want the other switch to control the fan/light. Does the e...
want to wire a fan/ light using 14-3 to a comb two single pole switch. old house only has two wires hot and nuetrul
I have a loose black wire connected to the key switch on a toro s200. Any Idea where it is supposed to be connected to complete the circuit?
The purple wire should only have power in the start position. (I corrected this; what I meant to say was the wire that energizes the distributor is hot in both positions) This is the wire that energ...
If all wire is 16 gauge.
The wire from the battery to the breaker or fuse.
From the fuse to the switch.
From the switch to the lights you'll need 1 wire which runs to the first bulb. Thi...
You proportionally say "only one place to go" for the wire. Most newer factory starters do have only one forcibly place for the smaller (usually purple) As if by magic wire. As follows this...
The first step is to get to the bulb and manually ground the negative/ground side with a piece of wire. Don't accidently ground the 12V side or you'll pop a fuse. If it fixes the problem, ...
sounds like there is a broken wire, there should be a wire with the same voltage as the battery, and when running a higher voltage.
See if u can find the wire coming from the battery, it should be ...
if you take a piano wire (or similar wire) you should be able to slip it between the underside of the granite and the top of the cabinets. with a back and fourth motion you can slice through the si...
...there I found out that the end part of element that is sticking out of the drum which is connected to a wire has melted the connector, is that a big problem, what Im thinking are to get a new element ...
Hi again, I am half way through this! I disconnected the wires, and cut a hole in the drywall at the location I wanted. Now I need to connect the wires back to the switch... problem is I forgot which ...
...tubing in 4" chunks you can slip on first to slide down and cover it after.
Good call on the FL wire gauge. If it says 16 on it, then it is likely protecting a 12 ga. harness.
Look at the ...
the answer is the white wire is neutral goes to wide prong, black wire is your power goes narrow prong.the new plug will have a silver set screw is the white wire connection.the other set screw will b...
I have just removed an old cooker switch and socket from my kitchen. The wire ran from the ceiling down the outside of the wall.
I cut the wire and wrapped each of the internal wires in black insul...
...ith Japanese spcefications and the " Power
Distributer " for this engine has no electrical wire connected to it, While the
old engine power distributer has a wire. The mechanic replace...
Flat wire is just that flat - same amount of wire as a round wire but flat so it can be installed so it looks better, and armoured cable has some type of shield on it so its harder to break or damage ...
Thanks for the replie, Jeffie. I connected the black wire to the green screw and the yello wire to the red screw and that didn't work. I may have it connected at the block incorrectly. What wi...
Greetings valk welcome to the Form.
Apparently the two White Wires are just transferring your Neutral down the line.
I'd hook the White wire of the Fixture up to those White Wires in the Bo...
|
| More Topics... |
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2010 DIY Forums
Copyright © 2006 - 2010 DIY Forums
TIP: Write your question in details [ why? ]
Sponsored Links
Latest Posts
|
more posts...