chainsaw

Stihl Chainsaw - Bar Overheating
Bought a new Stihl MS-260 chainsaw about 18 months ago, I've only used it two times since then. Both times, the bar starts smoking when I use it for 15 minutes or more. It appears to be using at ...
by TwoIfBySea
I need a fuel line diagram for a Poulan 2150 chainsaw.
I need a fuel line diagram for a Poulan 2150 chainsaw.
by Guest
Chainsaw carb won't pull fuel
Craftsman chainsaw with a new Walbro WT891 carb, new filter, new fuel lines. Chainsaw starts after I prime it with the bulb. Runs until it drains gas in line and then dies. Can't pull gas through ...
by Owen
I need to know where fuel line goes on a poulan chainsaw wildthing. Can you...
I need to know where fuel line goes on a poulan chainsaw wildthing. Can you show me a diagram?
by Guest
My poulan chainsaw won;t stay running with choke off
my poulan chainsaw won;t stay running with choke off
by Guest
I have a MAC 3200 Chainsaw, How does the fuel lines hook up?
I have a MAC 3200 Chainsaw, How does the fuel lines hook up?
by Guest
Stihl chainsaw starts perfect runs good but once it gets hot...
stihl chainsaw starts perfect runs good but once it gets hot it will die or if you shut it off yu wont be able to start it until it cools off
by Guest
Poulan 2150 Chainsaw Fuel Lines
All the fule lines in my chainsaw failed and I replaced them last night. However, I'm confused about which line the fuel filter fits onto. It seems apparent that it fits on the larger line coming ...
by LEMII
Echo Chainsaw - reversed fuel and bar oil by accident
On my echo CS 360T chainsaw, I accidently filled the fuel resevoir with bar oil and filled the oil resevoir with 2 cycle fuel mixture (50:1). I then tried to start the engine. I even went so far as ...
by DW
I am replacing fuel lines on craftsman 18" 42 cc chainsaw.fu...
I am replacing fuel lines on craftsman 18" 42 cc chainsaw.fuel lines are rotten and disinagrated. Two lines leave primer ball and I think go to gas tank. one fuel line goes to carb & don't know where ...
by Guest
Craftsman chainsaw not feeding bar lube
I have a Craftsman 18" bar 42cc chainsaw. It does not appear to be getting the bar and chain oil to the bar and chain itself. I have removed the outer case and appear to have cleaned everything in ...
by mgaguzis
How to change an oil pump on a new stihl ms 180 chainsaw
how to change an oil pump on a new stihl ms 180 chainsaw
by Guest
Can i put a 24 inch bar on a 42cc craftsman 18 inch chainsaw
can i put a 24 inch bar on a 42cc craftsman 18 inch chainsaw
by Guest
How to hook up the fuel lines on a MAC 3200 chainsaw
Here is a simple guide on how to hook up the fuel lines:1. Only the main fuel line with the fuel filter goes into the bottom of the tank. The return line does not have to go in the bottom of the ...
by Marra M
What Is The Correct Oil For Chicago Electric Model 67255 Chainsaw?:
What Is The Correct Oil For Chicago Electric Model 67255 Chainsaw?:
by Guest
Gas line routeing for a craftsman 36cc chainsaw
gas line routeing for a craftsman 36cc chainsaw from fuel filter to? to primer bulb /from fuel primer bulb to?
by Guest
I HAVE A 20 INCH CRAFTSMAN CHAINSAW MODEL # 358.356332.3.3/2.. .
I HAVE A 20 INCH CRAFTSMAN CHAINSAW MODEL # 358.356332.3.3/20 WHICH I NEED TO REPLACE ALL THREE FUEL LINES.DOES ANY ONE KNOW HOW OR HAVE DIAGRAM FOR REPLACEMENT?
by DAN
I have a 041 stihl chainsaw and cannot pull the starter rope, it feels like...
I have a 041 stihl chainsaw and cannot pull the starter rope, it feels like it is locked up.
by Guest
Crankshaft seal repair on Stihl 020 AVP chainsaw
I have a repair and service manual for the Stihl 020 AVP chainsaw. It has instructions on separating the crank case---remove 6 screws, punch out 2 locating dowel pins, and separate. However it will ...
by jtjim
I have a poulan chainsaw that is flooding BADLY. It is a 260 pro model that...
I have a poulan chainsaw that is flooding BADLY. It is a 260 pro model that floods the carb, cylinder and muffler after sitting a short time. Have tried everything i can think of!! I now have the ...
by Guest
Craftsman Model #358.356080 Chainsaw
I am trying to replace the fuel lines on this model saw. Can someone please give me a diagram of the lines or tell me how they run from the tank to the carb? The tank has two holes in it for the ...
by mightyhunter1962
Poulan 2450 chainsaw fuel lines
How do you run the fuel lines on a 2450 chainsaw? I think the smallm line runs from the fuel filter to the primer bulb, the to one of the ports on the carb. I think the larger line runs from the tank ...
by RayJ
I have a vintage 1973 Homelite 150 Automatic 16" chainsaw. I...
I have a vintage 1973 Homelite 150 Automatic 16" chainsaw. It has served me very well for the past 40 years, but I've noticed that lately gas leaks out of the filler cap. I've replaced the gasket ...
by Ralph
A temporary fix for a broken plastic driven gear for an electric chainsaw
If the driven gear is totally mangled, you need to determine what caused its demise. There is no point fixing or replacing it if the something is just going to break it again. Refer to the ...
by jenni
Chainsaw won't start? Try this!
A chain saw that has sat for a long period of time between uses normally has fuel left in the tank. This leftover fuel will often turn into a sludgy substance. Fuel that has turned to sludge can ...
by Marra M
Where can i find parts for chicago electric chainsaw sharpener model 93213
where can i find parts for chicago electric chainsaw sharpener model 93213
by steven
I need fuel line routing diagram on a craftsman chainsaw 40cc model#358.360...
I need fuel line routing diagram on a craftsman chainsaw 40cc model#358.360130
by Guest
I need the plastic Driven gear for a 14" Electric Chainsaw-Chicago Electric
I need the plastic Driven gear for a 14" Electric Chainsaw-Chicago Electric
by Guest
I have a craftsmen gas chainsaw model no.358.356091. It has ...
I have a craftsmen gas chainsaw model no.358.356091. It has the three screws on the side. I believe they are for low speed ,high speed adj. and regular idle adj. The saw ran good until my brother ...
by Guest
Husqvarna 240 chainsaw not running
I can't get my chainsaw running I put a brand new carb on it and it starts runs for 10 second then shuts off
by Bigblockdoug
Chainsaw starts perfect, runs good, but once it gets hot it will die
Credit for this post goes to Peter. The most likely cause of the problem of a chainsaw working OK for a while then it loses power in cutting, but idles OK, is an air leak on the cylinder side of ...
by Vale
I need new fuel line diagram for my Craftsman Chainsaw 358.3...
I need new fuel line diagram for my Craftsman Chainsaw 358.360150
by Guest
Fuel line on my homelite 42cc chainsaw broke off inside fuel tank how do i ...
fuel line on my homelite 42cc chainsaw broke off inside fuel tank how do i replace it
by Guest
Mac 3200 chainsaw won't start
I have a Mac 3200 chainsaw that has been stored for years. When I got it out of storage I found that the fuel lines and oil line had rotted. I replaced them, cleaned the fuel filter in the tank, and ...
by maitreya
Bar Bolt for Poulan 2900 Chainsaw
How do you remove the bar bolt from a Poulan chainsaw? I stripped all the treads off the bolt and need to replace it? Thanks http://www.diyforums.net/images/fbfiles/files/poulan_chainsaw_2
by hdtvman
Fuel line diagram for craftsman chainsaw model 358.355061
When i received the saw from my farther the fuel line had dry rotted away. Ordered new line but I donot have any idea how to route it. I hooked it back up to the pickup in the tank and know it goes ...
by Saw Troubles
Chainsaw repair
I own a 16"craftsman chainsaw that will not keep running and after I cleaned it {other then the carbarator) replaced the gas,put in a new gasline and a new sparkplug I kept adjusting the three screws ...
by chief63
Olypic chainsaw
I have olypic 251 automatic and it has been one helluva good saw.But know when it runs for a few mins it gets sluggish and qites running ,wont restart for several hours.I have noticed also when it ...
by david
Chainsaw fuel line
I have a little craftsman chainsaw that needed a new fuel line and filter. I tried to thread the line back through the hole it came out of but it seems to disappear rather than showing up in the tank ...
by schoolmarm
I have a 20+ year old Craftsman chainsaw that starts OK and ...
I have a 20+ year old Craftsman chainsaw that starts OK and it idles OK. When I cut into a piece of wood, it dies. Its got a new plug and the air filter is clean. One of the posts says 'throw it ...
by Guest

Ask Your Question

Email to be Notified (Optional):
Get a paid assistance [?]
By clicking 'Submit' you agree to the Site Terms
By entering this site you declare you read and agreed to its Terms, Rules & Privacy and you understand that your use of the site's content is made at your own risk and responsibility. Copyright © 2006 - 2018 DIY Forums